T2 Generator 480 V Line Load Zz = 1.5 + j 102 480/14,400 V 1000 kVA R = 0.010 pu X = 0.040 pu 14,400/480 V 500 kVA ZLoad = R = 0.020 pu X = 0.085 pu 0.45436.87°2 Y-connected In the transmission system shown in the figure above, the rated kVA of transformer 1, T1, is 1000 kVA and the rated kVA of transformer 2, T2, is 500 kVA. Transformers pu impedances are given on their rated powers. What is the real power in kWatts supplied to the load?

T2 Generator 480 V Line Load Zz = 1.5 + j 102 480/14,400 V 1000 kVA R = 0.010 pu X = 0.040 pu 14,400/480 V 500 kVA ZLoad = R = 0.020 pu X = 0.085 pu 0.45436.87°2 Y-connected In the transmission system shown in the figure above, the rated kVA of transformer 1, T1, is 1000 kVA and the rated kVA of transformer 2, T2, is 500 kVA. Transformers pu impedances are given on their rated powers. What is the real power in kWatts supplied to the load?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

A single phase 9.6 kVA, 500 V / 1.5 kV transformer has an impedance of 1.302 Ω with respect to primary side. and secondary sides. Find its per-unit impedance with respect to primary side only a. 0.02 b. 0.03 c. 0.04 d. 0.05
In single phase transformer, if the primary turns N1 is greater than the secondary turns N2, then what is the relation between V1 and V2? a.V1 < V2 b.V2 > V1 c.V1 > V2 d.V1 = V2
i need the answer quickly
9
In single phase transformer, if the secondary turns N2 is greater than the primary turns N1, then what is the relation between V2 and V1? O a. V2 = V1 O b. V2 > V1 O c. V1 < V2 O d. V2 < V1
In the transformer circuit below, a load of 2.5cis20° Ohms is connected to the output terminals of the transformer. If the voltage across the load is 230V, determine:a. Load current, I(L)b. Imc. Icd. Source voltage, V
Two transformers are to be operated in parallel such that they share load in proportion to their KVA rating. The rating of the first transformer is 500 kVA and its pu leakage impedance is 0.05 pu. If the rating of second transformer is 250 kVA, then its pu leakage impedance is A 0.20 B 0.10 C 0.05 D 0.025
When the transformer is loaded in a balanced fashion up to its nominal rating (10 MVA), calculate the high side line-to-line phasor voltages (ab, bc, ca). and low side phasor voltages both line-to-line and line-to-neutral (ab, bc, ca, a, b,c). as a reference for calculations the low side A line to neutral voltage is 7620V at an angle of 0 degrees when the transformer is at rated power. The transformer has the following characteristics: V: 138kV delta high side/ 13.2 kV wye low side 9% impedance X/R ratio of 20
A 120 kVA, 1350/330 V single phase transformer has the following parameters: R1 = 0.34 Q, X1 = 0.59 0, R2 = 0.014 Q, X1 = 0.029 Q, Rc = 380 and Xm = 320 Q. The no load current is 4.7 A at a power factor of 0.36 lagging and the no load losses are 4.6 kW. For a full load and 0.9 power factor lagging with 300 V load terminal voltage, determine (a) equivalent circuit parameters referred to primary side, (b) percentage regulation and (c) full load efficiency. O:01 AM
4. 100 kVA, 6800-240 V, 50 Hz single phase step down transformer has the following parameters: RLs-0.008Ω RHs-2.6Ω Ri-HS-500 0Ω XLS-0.015Ω XHs=5.22 Xm,HS=88002 Transformer is delivering 80% of rated load at rated voltage and 0.95 lagging power factor. Determine the following: a) The equivalent impedance of the transformer referred to primary. b) Input impedance of the combined transformer and load. c) Actual input voltage at HV side. d) Input impedance if load is disconnected. e) Exciting current at no load.
What is phase angle of voltage induced in primary and secondary windings of transformers due to mutual flux? Same Opposite Zero None of option
Topic- basic & const.