Answered: T₁ T2 T3 60° 40° x

Engineering

Civil Engineering

T₁ T2 T3 60° 40° x

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A built-up section is used as a structural member for a two-storey structure. Two channels and angle bars are to be welded to a rolled W section as shown. Determine the following if every section have dimensions in inches equal to : a= 11.10, b= 3.05, c= 0.50, d=3 , e=1/2, f=18.60, g=11.10, h= 0.535, i= 0.87 * Compute the section modulus of the composite section: Use S= Ix/ c, where Ix = moment of inertia of built up section, c= distance from neutral axis to the topmost/ bottommost fiber of the built up section. Compute the radius of gyration with respect to the x-axis Centroidal moment of inertia with respect to the y-axis. Centroidal moment of inertia with respect to the x-axis. Compute the radius of gyration with respect to the y-axis pls help me solve this (T___T) P.S : 3 decimal places
(Figure 1) Figure 1 of 1 C 3 ft Part A If yn = 1.5 ft, determine the largest weight of the crate so that neither cable segment AB, BC, or CD is subjected to a tension that exceeds 250 lb. Express your answer using three significant figures and include the appropriate units. Wmax= Submit Part B ZE Value Submit 4 → Value Units My Answers Give Up Determine the corresponding placement of the box, a Express your answer using three significant figures and include the appropriate units. μA 4 → C Units C My Answers Give Up ? ?
Show fbd and complete solutions
The uniform concrete slab has a mass of 2900 kg. The slab is held in the horizontal plane by three parallel supporting cables as shown. Suppose that F = 10 kN. (Figure 1) Part A Determine the tension in the cable connected to A. Express your answer to three significant figures and include the appropriate units. Part B Determine the tension in the cable connected to B. Express your answer to three significant figures and include the appropriate units. Part C Determine the tension in the cable connected to C. Express your answer to three significant figures and include the appropriate units.
Determine the degree of indeterminacy of the trusses as shown.
Question 29 An A36 angle bar is used as a tension member connected on both legs with 20 mm . Given that s = 60 mm, calculate the design strength (kN) by LRFD with the limiting state of tensile yielding in the gross area. Write your answer to the nearest whole number. Ag = 1,852 mm2 t = 8 mm
SHOW COMPLETE WORK AND FBD
3. Show that the bolted connection between a bracket 8 mm thick and the flange of an ISHB 400 can carry a vertical load of 100 kN as shown in the figure below. Assume M20 bolts, grade 8.8. 100 kN 250 200 60 60 140 Fig. El Section properties of ISHB 400: Weight per metre (kg) = 82.2 Sectional Area (cm²) = 104.66 Depth of section (mm) = 400 Width of flange (mm) = 250 Thickness of flange (mm) = 12.7 Thickness of web (mm) = 10.6
I need the answer as soon as possible
Situation 1| Consider the figure 1 below. 3- 25mmØ bolts are used to fasten a plate to a steel beam. 1) Determine the average shearing stress caused in each bolt by the 30kN loads 2) Determine the value of additional load P that must be applied so that each bolt will not exceed the maximum shearing stress of 60MPA. 30 kN 150. 300 200 30 kN P.
what is the tension in the bottom hoop due to fluid?
hi im stuck in this please help me out A wooden beam is loaded by a concentrated load ?P = 5000 N and supported by boundary conditions as shown in Figure Q5(a). The cross-section of the beam is shown in Figure Q5(b). Given that ???LAB = 3000 mm, ???LBC = 2000 mm, ?0B0=10 mm, ?1B1 = 30 mm, and ?H = 240 mm, ℎ0h0=200 mm, ℎ1h1=20 mm, determine the following quantities below: last two sub parts of question didnt fit in so i will type here- theres no question d e) Determine the maximum magnitude of shear force and bending moment, neglecting the sign. The maximum magnitude of internal shear force, positive value: N The maximum magnitude of internal bending moment, positive value: N*mm f) Determine the magnitude of the maximum bending stress in the beam, neglecting the sign. Maximum bending stress, positive value: MPa