T 5 m A -12 m B 100 kg

Q: A tape 30 m long, 0.6 cm wide and 0.5 thick was used to measure a distance of 000 m at a temperature…

A: Given- Measured distance Lm=999.75 mStandard temperature To=20o CField temperature T=35o CActual…

Q: 7. What is the potential energy of the 100-N block? 3 2 m Datum a. 50 J b. 100 J

A: Weight of the block = mg = 100 N . Height above datum = h =2 m . The potential energy  depends upon…

Q: The Army’s new ATPS personnel parachute is said to beable to bring a 400-lbf load, trooper plus…

A:

Q: 50 kN 30 kN- 3 m GH 30 kN- 3 m E 30 kN– 3 m

A:

Q: If Froude's law of similitude exists between a model and a prototype then the power ratio P, is

A:

Q: 400 lb F1 = 400i F2 = -600 k F3 = 500 sin 45 i-500 cos 45 k 7' 600 lb M,- rXF,, M,- 12XF, M,- rgxF,…

A:

Q: SOLVE FOR THE MOMENT OF JOINT , TABULAR AND STATE WHETHER TENSILE OR COMPRESSION

A:

Q: solve for member BD and CE

A:

Q: Situation 1: A W8x67 has a length of 7.50 m. Fy- 248 MPa. The properties are given below. Properties…

A:

Q: Find 41 as shown in the figure below. All ctimenvion are in millimeters Express answer in Dms 1OG2…

A:

Q: O. Which one of the following is the dimension of specific gravity of a liquid? a) [M' L3 T°J. b)…

A: To find :- dimension of specific gravity of liquid

Q: which bar is stronger A or B? assume that the given load are the maximum load each can carry.

A:

Q: Block A has a mass of 100 kg and the coefficient of friction is 0.20. Determine the friction force…

A:

Q: 1-77 For the beam shown in Fig. P1-77, determine a. The reactions at supports A and B. b. The…

A:

Q: A RA 4 ft 900 lb B 60 lb/ft 8ft. C Rc 6 ft 400 lb D

A:

Q: Q2. Analyze the following frame as shown in the figure. AB has 21, BC has 1.51, and BD has I. 120 kN…

A: carry over moment -  its the moment developed at one end due to applied moment at other end .  when…

Q: Part A Determine the moment of inertia of the beam's cross-sectional area about the y axis. Set a =…

A:

Q: A beam has a width of 200mm and a height of 250mm and is loaded as shown. Solve the moment of…

A: Given data in question  UDL 6kN/m Span 10 m Point load 28 kN Width 200 mm Height 250 mm To find out…

Q: What is the Final Moment in B for the 300 lb 300 lb 135 lb/ft given beam? a. 640 lb-ft b. 1077 lb-ft…

A: It is the beam that is most commonly subjected to bending moments. As the sum of the moments about a…

Q: The typical units of Cc and Cr are: O Ib/ft? and kPa O Ib/ft and kN/m3 O inches or milimeters O…

A: step 1-

Q: Which of the following stability value for Marshall design is not comply with the standard? O 750 kg…

A: Expansion :- The Marshall stability value is defined as maximum load carried by a compact specimen…

Q: A rectangular tank full of water is 2ft wide and 18in deep. What is the force due to water pressure…

A:

Q: Determine the moment of inertia of the beam cross section about the 20 mm 160 mm 4'1 20 mm -100 mm…

A:

Q: Situation 3: A W10x100 has a length of 9.10 m. Fy = 248 MPa. The properties are given below.…

A:

Q: Problem 4: Mario was broken hearted and trying to commit suicide, he tied a flexible rope of 7mm in…

A:

Q: Calculate the force in member BG using a freebody diagram of the rigid member ABC. The force is…

A: The given figure is shown below:

Q: 1500 lb 4500 lb ft E В D 6 ft 6 ft 3 ft

A:

Q: Q3: Draw the S.F and B. M. diagrams for the beam shown below. P = 625 lb L1 = 4 ft q = 80 lb/ft L2 =…

A:

Q: From the following figure, calculate the total area of Steel? COLUMN Y 10 - 250 2 m 2 m Select one:…

A: Given Steel bar diameter, d = 10 mm Spacing, S = 250mm centre to centre Length, L = 2m = 2000 mm To…

Q: P 150⁰ B O 1m A 2m O

A: Now we have to find the ratio of extension of rod A to that of rod B

Q: What is the distance between the front and rear axle of H Truck in meters?

A: the distance between the front and rear axle of H Truck in meters is equal to the distance between…

Q: The 1-kg block Band 10-kg cylinder A are connected to a light cord that passes through a hole in the…

A:

Q: Define Gmm, VTM, VMA and VFA. V₁ + V be be *100= V₁ VMA=- 100-G mb Deduce the following equations:…

A: Given that :-As we know that :so, if weight of constituents are given in percent of total mix ;where…

Q: Q6) What is the value of the applied force (lbf) on the square panel with dimensions of 4 in by 4 in…

A:

Q: Determine the forces in members BC, BG, and FG

A:

Q: F i n d   t h e   r e s u l t a n t   o f   t h e   f o r c e   s y s t e m   s  h o w n .  P=281…

A:

Q: U=2.55 m/s a=1.2 m/s2 t=2 s Find final velocity of car

A: Introduction : The given question is related with mechanics . In this question we are provided with…

Unit Conversion

Standard units are also called SI units. SI units are used for measuring a physical quantity satisfying certain conditions. There are two types of units: fundamental units and derived units. Fundamental units are physical quantities that are independent, that is, they do not depend on other quantities like mass, length, or time. There are plenty of quantities in our lives which need to be measured and compared. Measuring is the comparison of a particular physical quantity with its reference value. A unit is a measure of a fixed physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.