Surface Water Budget 2017 Percentage to Long term Rate Hydrological Volumes Percentage to Long-term Rainfall in MCM elements Rate Rainfall Volume 8165 8206 99.5% Evaporation 7636 93.5% 7582 101% Floods 167 2.1% 196 85.2% Groundwater 362 4.4% 417 86.8% Recharge calculate the percentage to rainfall and percentage to long term rate

Q: Jse commands (rectangle, mirror) and List he commands to draw the following drawing start from a…

A:

Q: Determine external as well as total indeterminacy

A: Given data : Number of External support reaction (R)=2+2=4Number of member (m)=6Number  of joint…

Q: is one of the option to change the line Thickness. a. Zoom b. Linear c Bylaver

A: Zoom-  The function of this tool is to alter the zoom level of any working image.  Linear-This…

Q: Compute Ix for the region shown. y 2 18 2-5--5- -2 -8 8. Dimensions in inches

A: The area is divided into the standard areas as shown below.

Q: -160 40 160 Dimensions 40 in mm 40 -160- –160-

A:

Q: Explain the formula of fs

A: From the original solution: Given: Width, b = 18 in Effective depth, d = 26.5+2.5=29 in. Height of…

Q: A clockwise couple M = 4.5 N m is resisted by the shaft of the electric motor. (Figure 1) Part A…

A: Given: The moment M is 4.5 N.m. Consider the figure,

Q: 13.1500 13.1500 4 0000 - -2.0000 4.0000 -3.3500 0.0000 2.0000- 3.8000 -3.3500 2.0000 2.0000 2.0000…

A: We need to find out One Way Slab and Two way slab If Ly/Lx is equal to or more than 2 then One way…

Q: y 200 mm 300 mm → 125 mm 125 mm 60 mm 150 mm

A:

Q: For the given structures, determine the degree of indeterminacy. 6. T 6

A: The given beam has three support conditions. The Left end is a Fixed support.(3 reactions)…

Q: 16. From a triangular steel plate XYZ, a triangular section VWZ was cleanly cut off. What should be…

A:

Q: Find the Ix, Iy and J of the component

A: Consider the figure,

Q: 4- Which statement is true about the precedence of lines? A. a hidden line has precedence over a…

A:

Q: Determine the XT and YT(using both a and b) a. Using the Top Most, Left Most Reference Line b. Using…

A:

Q: Based on the graph, what is the best shape to lower the force acting ? Circle or rectangular? Make a…

A: For Circular Shape Column Centre of Gravity (hc) Diagonal Depth Centroid (yc) Diagonal Depth…

Q: Find the Xp ¢ YT Зст I}1:25 cm Cocn 61.5 cm 0.75 cm

A:

Q: What is the Ix and Iy of the cross-section in mm4

A: Given: Required : Ix and Iy of the cross-section in mm4

Q: Draw the NTM diagrams for frame on the picture. 90= F/a 10000 a 2a F = 1 kN a = 1 m

A:

Q: AAC both of the 800 800 T 1 P 1400 b 12 R

A:

Q: top wiew Units are in millimeter right side 40 IS 35 ーネィー ー子ィー front viw 1-..

A: Given orthographic views- Top view Front view Right side view

Q: aSN 200 mm 350 mm

A: Free Body Diagram (FBD):

Q: determine the degree of indeterminacy.

A: * Hinge support: - It is defined as the support which resists horizontal and vertical reaction but…

Q: Draw the influence lines for the vertical and horizontal reactions, Ax and Ay, at support A and the…

A: Question consist of truss supported at hinge support at A and G . Length of members are given in the…

Q: 80 mm -L- В D 60 mm

A:

Q: Z 10 mm 15 15 430 y y -y y 15 100 All dimension in mm FIGURE Q3 (a) FIGURE Q3 (b) IN

A: The dimensions of channel section are given.two channel sections are arranged back to back with 10mm…

Q: (0 KN 15KN DU む oam 0.am J 1.2met>2mt l.zmel

A:

Q: 643-218

A: Note: As you have nothing mentioned in this problem. So, we are assuming that we have to apply…

Q: show the (c)

A:

Q: 200 mm 200 mm 400 mm

A: Section  Area  x Remarks  ABC A1  = π42002      = 31400 mm2 x1 = D2    = 2002     =100 mm   AEF…

Q: 4x-2x2+1 find lim, 3x-5

A:

Q: 3. A simply supported beam of 6 m, see cross-section below is subjected to a concentrated load of…

A: Using bending equation

Q: What are the internal forces at point C of the beam

A: Find reactions:∑ MB=0RA12-500126-900+900=0RA=3000lbFind reactions:∑ Fy=0RA+RB-50012=0RB=3000lb

Q: 4) A precast T beam with the dimensions shown below is to be a used as a bridge over a small…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: 3. Is Iust be par PROBLEM 1: The frame shown is supported with hinges at A and C and a pin at B.…

A: Both the hinges will have the two supports, they are :- RAx and RAy at A and RCx and RCy at C. Then…

Types of Composite

Composite materials are formed by merging two components that have different chemical and physical properties. The merged output is termed as a composite, whose properties are completely different from the individual components. Composite materials also have better strength than the individual components.Composite materials usually have two main parts, reinforcement material, and matrix material. The matrix material acts as a binder and surrounds the fiber of another material that bears a much higher strength. This material is known as the reinforcement material. The matrix materials are usually high-strength additives resins, while the fibers of the reinforced material can be random, oriented, and in a mat format.Composite materials are also known as fiber-reinforced composite polymers because they are composed of the polymer matrix which is reinforced to laboratory-created fibers or naturally occurring fibers, such as glass fibers, carbon fibers, or aramid fibers. Under the application of external loads, the matrix material absorbs and transfers the loads to the fibers, these fibers in return provide good compressive strength, tensile strength, and stiffness to the fiber-reinforced composite materials.Depending upon the matrix and the reinforcement material, different properties can be induced to the fiber-reinforced composite materials, including good corrosion resistance properties. The most common matrix material is the resin while the glass fibers act as the reinforcement material. Strong fibers provide strength and stiffness to the composite materials while, a soft and flexible resin provides shape to the composite materials.