Supposed you use an ideal pulley of the type shown in pic to support a car engine o mass 125 kg. What's the tension in the rope? What force must the ceiling supply assuming you pull straight down on the rope? Neglect the pulley system mass

Supposed you use an ideal pulley of the type shown in pic to support a car engine o mass 125 kg. What's the tension in the rope? What force must the ceiling supply assuming you pull straight down on the rope? Neglect the pulley system mass

College Physics

11th Edition

ISBN:9781305952300

Author:Raymond A. Serway, Chris Vuille

Publisher:Raymond A. Serway, Chris Vuille

Chapter1: Units, Trigonometry. And Vectors

Section: Chapter Questions

Problem 1CQ: Estimate the order of magnitude of the length, in meters, of each of the following; (a) a mouse, (b)...

See similar textbooks

Similar questions

Calculate how much labor you and a buddy put in when each of you pushes a vehicle that has run out of gas. Assume that you and your buddy each exert a horizontal force of 200 N over a distance of 100 m.
A motor boat moves at a steady speed of 2 m/s. Water - resistance acting on it is 2400 N. Calculate the power of its engine ?
What are the magnitude (F) and the location measured from end A (d) of the equivalent resultant force of the triangular distributed load in the figure below. S m 3 m Wo =7 kN/m Select one: O a. F = 6 KN; d = 1 m O b. F= 6 KN; d= 6.5 m O C. F= 10.5 KN ; d= 6 m O d. F= 21 KN ; d= 6 m Activate WindoFinish attempt. Go to Settings to act 21:55 S ACTIVITY Ca ) ENG 17/04/2021
A block, m, , is on a frictionless ramp. A rope is attached to this block. The rope goes over a pulley. The other end of the rope is attached to the ceiling. A second block, m, , is attached to a pulley that hangs from this rope. The pulleys are both massless and frictionless. The setup is shown in the image below. (Use 0 = 30°, m, = 40kg and m, =10kg.) %3D What are the magnitudes of the accelerations of each block? b. What is the tension in the rope? а. m, m2
4. How much power is needed for a power motor to lift a 385-kg metal box in a cargo aircraft for 12.0 s if the height of the aircraft door is 4.0 m above the ground?
Hang the spring balance on the right side of the lever at the 10 mark and pull the spring balance so that the lever comes into a horizontal position. (ii) Read the indicated value of force meter and record it in Table 1 on the Results page. (iv) Move the load successively to the 8, 6, 4 and 2 marks on the left side and measure the force for each position and record it in Table 1 on the Results page. Question – 1: Using the mass m, calculate the load (force) and record it above the table – 1. Question – 2: From the distance between the marks used (2 cm each), calculate the length of the load arm di and the force arm di in cm and add these values to the result tables. Question – 3: Calculate the products L × di und F x dh and record these values in the result tables. Mass = 100 g, Load (L) = 980 N TABLE - 1 Objects di (cm) L x di (Ncm) F (N) d2 (cm) Fx d2 (Ncm) Left Right side side Load Force 10 10 1.0 8 10 0.78 6 10 0.58 4 10 0.40 2 10 0.20
45. Suppose a person uses a mechanical jack to lift one half the weight of a car with a mass of 1200 kg. During each stroke of the jack handle, the person’s hand is pushing for a distance of 40.0 cm but the car is lifted only 5.0 mm. (a) Assuming the jack is 100% efficient, how much force must the person exert on the handle as the car is lifted? (b) If the actual amount of force required on the handle is 90.0 N, what is the actual efficiency of the jack?
Needs Complete typed solution with 100 % accuracy. Don't use chat gpt or ai i definitely upvote you.
Based on the given please answer the two question What is the fulcrum? What is the effort?
The vertical spring shown below stretches 2 inches with a 1 kg weight suspended from it. By how much does the horizontal spring stretch if it is the exact same spring?
4) Suppose you use an ideal pulley of the type shown in image (a) in the figure below to support a car engine of mass 135 kg. (a) MA = 2 W (b) MA - 3 (a) What would be the tension in newtons in the rope? (c) MA 4 (b) What force in newtons must the ceiling supply, assuming you pull straight down on the rope? Neglect the pulley system's mass.