Şuppose you have a wind speed gauge like the pitot tube shown in figure below. By what factor must wind speed increase to double the value of h in the manometer? Is this independent of the moving fluid and the fluid in the manometer? V, = 0 Figure caption: Meașurement of fluid speed bạsed on Bernoulli's principle. This type of velocity measuring device is a Prandtl tube, also known as a pitot tube. Is this independent of the moving fluid and the fluid in the manometer? O Yes

Şuppose you have a wind speed gauge like the pitot tube shown in figure below. By what factor must wind speed increase to double the value of h in the manometer? Is this independent of the moving fluid and the fluid in the manometer? V, = 0 Figure caption: Meașurement of fluid speed bạsed on Bernoulli's principle. This type of velocity measuring device is a Prandtl tube, also known as a pitot tube. Is this independent of the moving fluid and the fluid in the manometer? O Yes

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

C1 (a). A lubricating oil having the dynamic viscosity of 0.056 poise and specific gravity of 1.17. Calculate (i) the density of oil in kg/m3, (ii) the weight density of oil in N/m3, (iii) the kinematic viscosity in stokes, and (iv) the specific volume in m3/kg. C1 (b). The capillary effect in a glass tube of 2.8 mm diameter, when immersed in (1) water and (2) mercury are 7.7 mm and -3.5 mm respectively. Calculate the value of surface tension in contact with air for water and mercury in N/m. Take, the contact angle for water =0° and mercury =130°. C1(a). (i).the density of oil in kg/m3 C1(a). (ii) the weight density of oil in N/m3 C1(a). (iii) the kinematic viscosity in stokes C1(a). (iv) the specific volume in m3/kg C1 (b). 1.the value of surface tension (water) in N/m C1 (b). 2. the value of surface tension (mercury) in N/m
Fluid Statics Please provide a complete and readable solution for the problem if necessary and an explanation. Thank you!
3 what will be the kinematic viscosity of an oil having density 888 kg/m. The shear stress at a point in oil is 0.278 N/m and velocity gradient at that point is 0.2 per second.
A Pitot-static probe was used to measure the velocity distribution in a water tunnel. The two pressure lines from the probe were connected to a U-tube manometer which uses a liquid of specific gravity 1.7. The maximum velocity expected in the water tunnel was 2.3 m/s. Your job was to select an appropriate U-tube from a manufacturer which supplies manometers of different heights. The cost increases significantly with manometer height. Which of these should you purchase?
Calculations involving retention time involve the following formula, T =, where V is volume and Q is flow rate. Often times, you will be required to calculate the volume of more than one tank and determine a rate of flow, given a total retention time. Tank 1 Tank 2 Let's assume that the total retention time for the entire system is 55 minutes, and we want to know the inlet flow, given the dimensions of tank 1 are : 14m x 10m x 3 m, and tank 2 are: 5m x 10m x 3 m. Calculate the inlet flow.
An airplane that has a cross-sectional diameter D = 4 m of the front portion is to fly at a speed of 600 km/hr in air that has a density of 1.1 kg/m and dynamic viscosity of 1.27 x 10 Pa.s. A small size model of scale ratio (1/17) to be tested in a different fluid that has a dynamic viscosity 5 x 105 Pa .s and a density of 500 kg/m2. It is determined that the parameters that are important for this test are: diameter D, density, viscosity, velocity V, the length of the wings L and the drag force F. What must be the speed (m/s) of the model to Choose... ensure dynamical similitude? What must be the corresponding diameter of the model (cm)? Choose.. What is the number/s of dimensionless groups for this problem? Choose...
Problem 2 The apparatus sketched in the figure below serves as a viscometer i.e. it can be used to measure the viscosity of a liquid. In the drawing, D is a large reservoir containing a viscous liquid A and E is a cylindrical tube of radius R, open at both ends, surrounding and coaxial with B, which is a cylindrical "bob" of radius êR that is dragged up through the fluid by a frictionless pulley system (C) utilizing a weight W. Determine a design equation that relates the viscosity of the liquid to the geometry of the system and the weight W. Hint: you can assume that the length of the cylindrical tube is sufficiently long for the flow to reach steady state. W E D B
1 (a) A plate 0.05mm distant from a fixed plate moves at 1.15 m/s and required a force per unit area of 2.7 N/m2 to maintain this speed with using an oil of specific gravity 0.75. Find the dynamic viscosity and kinematic viscosity of the fluid between the plates. 1 (b) Calculate the specific weight, density, and the specific gravity of a liquid having a volume of 665150 cm³ and weight of 71 kN (ENTER ONLY THE VALUES BY REFERRING THE UNITS GIVEN) 1 (a) The dynamic viscosity of the fluid (in Centipoise) The kinematic viscosity of the fluid (in stokes) 1 (b) Specific Weight in (kN/m3) Density of liquid (in kg/m2) Specific gravity of liquid Windows bu
Velocity distribution of a fluid in a sliding plate viscometer is used to measure the viscosity of the fluid. The top plate is moving with force (F) with a constant velocity (V) as shown in the Figure below. Force (Ft)= 5 N, Velocity (V) = 10 m/s, Temperature = 100°F. Top plate (Area » Length = 0.1 m and width = 0.05 m spaced by 0.001 m) is moving and the bottom plate is stationary. Determine: The viscosity of the fluid. Which fluid is this? Is this fluid more, or less viscous than water? ● IN FLOW N-L