Suppose we have the instruction Load 100. Given memory and register R1 contain the decimal values below: Метory Content Address R1 200 100 500 300 700 500 900 700 100 900 300 Assuming R1 is implied in the indexed addressing mode, determine the actual value loaded into the accumulator and fill in the table below: Mode Immediate Value Loaded into AC Direct Indirect Indexed

Suppose we have the instruction Load 100. Given memory and register R1 contain the decimal values below: Метory Content Address R1 200 100 500 300 700 500 900 700 100 900 300 Assuming R1 is implied in the indexed addressing mode, determine the actual value loaded into the accumulator and fill in the table below: Mode Immediate Value Loaded into AC Direct Indirect Indexed

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

Assume AL=35h; CL=05. Write the content of AL after RCR AL, CL - showing the calculation steps. Assume a CLC instruction before this RCR instruction. (Note : Solve the question in paper, scan and upload along with the other Part B and C answers) A- BI E E I E
Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es. If applicable, determine the content of the destination after the execution of the instruction. Otherwise, NA. For physical address and content of the destination, use CAPITAL LETTERS,NO SPACE/S in between and NO need to include "H" or the unit. If the given register are fewer than required, just put zeroes in the most significant place. A -effective address B - physical address/es e.g. 19000-19001 C- is for addressing mode type, e.g. direct D- content of the destination after execution e.g. if register: AX=1234 if memory (lower address first): 12000=34;12001=12 3(2).JPG ... AX =6FFAH DX =BFA8H SS = 6FFEH SI %3D 2BCАН IP = FADEH ВХ -9CF5H CS =5FFEH ES = 8DBEH BP = 6EEFH CX =3FFEH DS =AF9EH DI = 5EC9H SP = 9AABEH MOV [BX+SI+ADBCH], ESP EFFECTIVE ADDRES: Blank 1 PHYSICAL ADDRESS/ES: Blank 2 ADDRESSING MODE : Blank 3 CONTENT OF THE DESTINATION: Blank 4
Consider a 16-bit processor in which the following appears in main memory, starting at location 200: B. The first part of the first word indicates that this instruction loads a value into an accumulator. The mode field specifies an addressing mode and if appropriate, indicates a source register; Assume that when used, the source register is R1, which has a value of 400. There is also an index register (XR) that contains 100. The value of 500 in location 201 may be part of the address calculation. Assume that location 399 contains the value 999, location 400 contains the value 1000, and so on. Determine the effective address and the operand to be loaded for the following address modes:
Write a PIC18 instruction sequence to initialize the contents of file registers at addresses from 0x077 until 0X07A with the value D'120'. You MUST use indirect addressing mode with file select register, FSR2 in your solution.
Determine the specific type of addressing mode (SMALL LETTERS only) and compute for the address/es. If applicable, determine the content of the destination after the execution of the instruction. Otherwise, NA. For physical address and content of the destination, use CAPITAL LETTERS,NO SPACE/S in between and NO need to include "H" or the unit. A - is for addressing mode type, e.g. directB - physical address/es e.g. 19000-19001 C - content of the destination after executione.g. if register: AX=1234 if memory (lower address first) : 12000=34;12001=12 GIVENDS = ACF7HSS = BAC9HDI = ECABHSI = ABAEHBP = BAD2HAX = 6FCBHBX = 7BCFHCX = 5CADHDX =D1BCHSP = 4FABH
Indirect Addressing Mode Instruction 002A J@ RETADR 3E2003 0030 RETADR RESW 1 Instruction Starts with 002A Opcode of J is 3C Object code is 3E2003 Show the detail work to get the above object code from the instruction. F9 F10 F11 F12 delet + ||
For the given values of D, shr, shr_in, Id, and clk, indicate the register's Q value. Dis 111, shr_in is 0, shr is 1, Id is 0, and Q is 101. clk rises. What does Q become? Function table thr Id | Register function IP shr in- 0 0 Maintain 01Lood 0 Shuft-right 1Maintain 13 12 i1 0 13 12 it 0 13 12 it 10 she st 4xl 4x1 4xl Block ymbol DFF OFF DFF to she in 3-bit ahift-rht/lend ragister she at ahirightad ld Pegiter O 010 O 110 O 101 O 111
An instruction is stored at location 100 with its address field at location 101.The address field has value 200. A processor register R1 contains the number 300. Evaluate the effective address if the addressing mode of the instruction is A. Direct B. Immediate C. Relative D. Register Indirect E. Index with R1 as the index Register
Please explain the difference between Register Direct Addressing and Register Indirect Addressing with proper examples. Please find the Machine code for the instruction: Mov 101A[BP+DI] , DL . Consider the Opcode fora Mov operation to be 10 00 10
Match segment and offsetregisters and determine their correspondingactual memory location addressed of the following real mode 80286 segment registers given below. Segment Register Effective Address 1. CS = 2010H 2. DS = 2100OH 3. ES = AB80H 4. SS = 1234H 5. DS = B20FH When: a. DI = 2000H d. IP = ABCDH b. BX = 100AH e. BP = 12FFH c. SP = 3A00H Type the address in uppercase. Do not forget to append H to each addresses. 1. EA: 2. EA: 3. EA: 4. EA:
Consider a 16-bit processor in which the following appears in the main memory, starting at location 200.a. The first part of the first word (content at 200) indicates that this instruction loads a value into an accumulator; the value of 300 in location 201 may be part of the address calculator. The mode field specifies an addressing mode and, if appropriate, indicates a source register. a. Assume that when used, the source register R1, which has a value of 500. b. There is also a base register that contains the value 100, Assume that location 249 contains the value 399, location 250 contains the value 400, and so on. Determine the effective address and the operand to be loaded for the following address modes:
liomework: Identify the addressing modes used for the source and destination operands, and then compute the physical address for the specified orx•rand in each of the following instructions: a) Mov +XYZ,AH (Destination operand) b) Mov tBX) (Destination operand) Suppose that BX=030016, 010016.