Suppose Vcc=10V, the transistors are matched with Is=33fA and B=200, and the resistors have the following values: R₁ R₂=5k and R3=R4=292. Let VBE = VEB=0.7V and V₁= 26mV a. For v₁=0, estimate the output resistance of the circuit.

Suppose Vcc=10V, the transistors are matched with Is=33fA and B=200, and the resistors have the following values: R₁ R₂=5k and R3=R4=292. Let VBE = VEB=0.7V and V₁= 26mV a. For v₁=0, estimate the output resistance of the circuit.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

1. The circuit shown in the figure is a/an a. XOR gate b. AND gate c. XNOR gate d. OR gate 2. From the circuit shown, if the inputs A and B are both 1, Q3 is/has a. in the active region b. saturated c. at cut-off d. a collector-emitter voltage equal to 0 V3. From the circuit shown, if the inputs A and B are 1 and 0 respectively, Q3 is/has a. at cut-off b. saturated c. in the active region d. a positive collector-base voltage4. From the circuit shown, if the inputs A and B are 0 and 1 respectively, Q5 is/has/will| a. a negative base-collector voltage b. a collector-emitter voltage approximately 0 V c. at cut-off d. cause the LED to turn off
Consider an n-channel metal-oxide-semiconductor field-effect transistor (MOSFET) with a gate-to-source voltage of 1.8 V. Assume that = 4, unCox 70 x 10-6 AV-2, the threshold voltage is 0.3 V, and the channel length modulation parameter is 0.09 V¹. In the saturation region, the drain conductance (in micro seimens) is - W L
5 Rib Vs (E The following parameter for this transistor, VCC = 5V, RL = 4k2, RE = 3kN, R1 = 60kN, and R2 = 40k2, B = 100 and VA = 160. Determine: a. ICQ and VECQ, b. AV, c. Ai. d. Ro
Question 1: For the Mosfet in the circuit shown below: VTp = - 0.8V, and Kp = 200 uA/V2. Find Vs and Vp. Where Kp = ½ kp'W/L. lo=0.4 m Vs R= 50 k2 Rp=S ka -5 V
2. The parameters of the transistor as shown in the figure below are ß = 100 and VA = 100V. a. Find the dc voltages at the base and emitter terminals. b. Find Rc such that VCEQ = 3.5V. c. Assuming Cc and CE act as short circuits, determine the small-signal voltage gain Av = Vo/Vs. d. Repeat part (c) if a 5000 source resistor is in series with the vs signal source. V+ = +5 V Rs = 100 £2 www Us Cc RB = 10 ΚΩ I= Iausmi 0.35 mA www RC -000 V=-5 V CE
In reference to the given figure, VCB = 10.3V and VBE = 0.7V. NOTES: VCB = VC-VB VBE = VB-VE In reference to Figure 2, given the dc load line and the transistor circuit, what will be the value of RC, in kilo-ohms? In reference to Figure 2, given the dc load line and the transistor circuit, what will be the voltage of RB, in volts? In reference to Figure 2, given the dc load line and the transistor circuit, what will be the value of RB in kilo-ohms, if Beta=100?
Common Gate MOSFET Amplifier has Select one: a. input is connected to the Gate and the output is taken from the Source b. input is connected to the Source and the output is taken from the Drain c. input is connected to the Gate and the output is taken from the Drain d. input is connected to the Source and the output is taken from the Gate 55 week 10 material Jump to... CE255/EE255 (01)- 16
Design a voltage divider biased CE stage with emitter degeneration. That stage should support a voltage gain of 5 and an input impedance larger than 3 KOhms with a bias current of 0.5 mA. Assume Beta=100, Is = 5e-17. Neglect the early voltage effect. You also need to provide values for the operating point of this transistor. Find the output resistance of this stage if the early voltage = 20 V.
To operate as an amplifier, it is the base of an npn transistor... Please select one: a. 0V b. positive by collector c. negative relative to emitter d. positive relative to emitter
An NPN bipolar junction transistor having VB > VE and Vc = (VB - 400 mV) is: Select one: O a. Operating in saturation. O b. Operating in deep saturation. O c. Operating in active mode. O d. Operating at the edge of soft saturation. In order to operate in the active mode. annpn transistor must have VBE 0 and Vec Select one: Tue
3. Given the circuit below, with all transistors identical. Assuming that VBE(ON) = 0.65V and Beta=25, what is R1 so that: a. lout= 1 mA when Vin=1V? b. lout= 2 mA when Vin=2V? Vn IN R lour Ic le Q4 Q,
Output Stages: Class AB Output Stage