Suppose -Vcc is connected to the ground, What happens to the LED when Vin< Vref and how?  What is the use of RL here and how is its value computed? Should the Vout also be connected to the ground?

Q: Why is a Cockcroft-Walton circuit preferred for voltage multiplier circuits? Explain its working…

A: Cockcroft Walton multipliers are prefered where very high voltages at relatively low currents are…

Q: At what junction offset are varicaps used

A: Given :   varicap is a PN junction diode which will works only in the reverse biased region.     In…

Q: I need a diagram of a circuit by the transform and rectification block, using the bridge rectifier…

A:

Q: this represents an OLTC system, taken from the matlab program, explain what the elements used are,…

A: A 25 kV distribution network consisting of three 30-km distribution feeders connected in parallel…

Q: 3. Write down which transistor structure each curve characteristic belongs to in the figure. VGs…

A:

Q: How do we know current flows in source terminal? Is this common for n-type mosfet? What is an n-type…

A: How do we know current flows in source terminal? Is this common for n-type mosfet? What is an n-type…

Q: What is Peak-Inverse-Voltage (PIV)? Why is it considered important?

A: Peak Inverse Voltage (PIV)  refer to the maximum voltage a diode or other device can withstand in…

Q: Subject name: Signal processing measurement Question: Is there any difference between the metallic…

A: Resistance is the property of opposition to the flow of current and is the important property of…

Q: Describe the purpose of a PV and PQ curves. Draw the curves and explain its position (stability &…

A: It is asked to describe the purpose of a PV and PQ curves. Aslo we need to draw the curves and…

Q: Question 6 R1 Vin V. R2 Figure Q6b : Op-Amp Circuit b) How would an inductive load affect rectifier…

A: b) A rectifier is a device which converts the alternating signal to approximate constant signal.…

Q: Draw the signal flow chart of the simple resistance network. a) Determine the variables. b)…

A: Given:-

Q: what is a demagnetizing factor and what is it used for? does it have any dimensions or units? what…

A: ANSWER DEMAGNITIZATION--&gt;     .…

Q: 20 V Ge C Vo 3 V= -20 V 19

A: We need to find out output voltage for given input .

Q: Explain the two types of MOSFETs (draw the physical structure as well). Also explain the major…

A:

Q: what is circuit breker ? function

A: Given: what is a circuit breaker? Required: Function of the circuit breaker

Q: Explaion the concept of RL Circuits in relation with Linear Equation?

A: RL circuit is a combination of resistance R and inductance L in a circuit supplied by a battery. It…

Q: Construct the Kelvin Double Bridge and describe the process to re- move the connection lead and…

A: Wheatstone Bridge- It is a circuit constructed to find the unknown resistance with the help of the…

Q: SEcIon A T ) Question 1: Hj w) vt) IH( AH(w) 4 For the system given above determine the output, yt)…

A:

Q: Set up a midpoint bias for a JFET with IDSS = 14 mA and VGS(off) = -10 V. Use a 24 V dc source as…

A: For the midpoint bias JFET, the drain current is calculated as:  ID=IDSS2IDSS=14 mAID=142 mAID=7 mA…

Q: How would you reduce Req of a circuit by adding a resistor – numerical piece to follow.

A:

Q: Could you please go into more detail about how the Ac equivilant model was created? thank you

A: The AC equivalent model of the circuit need to be explained for the given volt

Q: GIVE DETAIL EXPLAIN PLEASE! with cicruit drawing.. Ans : Rth = 28 ohm Vth = 92 V

A: Circuit is given as,

Q: Subject:Electronics Engineering How JFET has been constructed? Explain the principle of operation…

A:

Q: Sketch and describe mathematically the even and odd components of the signal shown in Figure (1)

A: given signal

Q: What are the DC collector currents IC1 and IC2?

A: In this question we need to find DC collector currents IC1 and IC2

Q: VDO for M1 mosfet Nn Cox (w)- Im Alv, VTN= 0,7V J0ONA VX %3D a) In wwhat condition does the masfet…

A:

Q: What is the importance of a full-wave bridge type power supply and its advantages and disadvantages?

A: Full bridge rectifiers are a type of bridge rectifier that may be used to power a wide range of…

Q: What is a comparator IC, and how do we use it?

A:

Q: Apply the junction rule to junction b in Figure. Is any new information gained by applying the…

A: The circuit is shown below:  At node b, the incoming current is I1 , the outgoing currents are I2…

Q: Subject:Electronics Engineering What is the main constructional difference between D-type and…

A: MOSFET: It stands for Metal oxide semiconductor field effect transistor. It is used as a voltage…

Q: XSC1 Ch.1 Ch.2 XSG1 10V / 1KHZ XMM1 XSC2 ER1 A -88769 Ch.1 Ch.2 R1 1K Graph of XSC2 Graph of XSC1 20…

A: We need to tell about peak voltage from given graph , we will tell by observing the graph . We also…

Q: Ģ V1 -0.1V 300 V2 0.3V V3 0.5V V4 0.7V U1 0.097u DC 1e-09Ohm DC 10MOhm 0.1 U3 6.883u DC 1e-090hm DC…

A: Given that: The circuits are shown below. Find the forward bias graph using the figure.

Q: What is sample and hold circuits?

A: A Sample and Hold Circuit (S/H Circuit or S &amp; H Circuit), is usually used with an Analog to…

Q: What is meant by FACTS in power systems? Discuss about SSSC type FACTS device.

A:

Q: What is the difference between an SCR and a TRIAC in AC?

A: The solution is given below