Suppose the heights H of 800 students are normally distributed with mean 66 inches and standard deviation 5 inches. Find the number N of students with heights between 65 and 70 inches? 505 225 294 345

Q: Do, parts d, e, f, h

A: If a body  vibrates without the help of any external force it is said to undergo free vibration The…

Q: Find MG

A: Data given Find : Metacentric height

Q: Calculate the equivalent concentrated force of distributed force diagram, draw the free body diagram…

A: Consider the free body diagram of the beam,

Q: How can I find GH, EG and FH

A:

Q: 3. Calculate the SDI for the following samples. Determine if the water needs to be pretreatment…

A: To calculate the SDI, we use the following formula:SDI = (1 - Ti / Tf) * 100 / Ttwhere:Ti is the…

Q: g) At what single point along the beam does this maximum occur? h) What are the values of internal…

A:

Q: Question 11 Construct the Shear and Moment diagrams COMPLETELY. Indicate all the abrupt change in…

A: A loaded beam is given and it has been asked to determine support reactions and shear force and…

Q: PC1 PI1 0+000 Lct PT1 R1 11 STATION NORTHINGS EASTINGS 0+000 11475.55 8927.24 PC2 9291.91 9546.66…

A: To Determine Table 3 ( The Stationing of PC, PT, PC2, PCC, PT2, PC3, PRC, PT3 and End of Project)…

Q: Label the maximum and minimum values on the graph. d) Draw the internal bending moment diagram (BMD)…

A:

Q: Q.4 X A plane blow leak velocity component u = y V=- and w = 0 along x, y T₂ and z direction…

A: Given- Leak velocity components- u=xT1,v=-yT2,w=0, It is needed to find the relation for blow to be…

Q: a) Compute the difference in elevation between A and B. b) Compute the difference in elevation…

A:

Q: Estimate the uplift pressure under bottom left corner of this dam If the entire dam sits 2ft below…

A: coefficient of permeability, Height, Height,

Q: Problem 2. A well is located in a completely confined aquifer with a hydraulic conductivity of 12…

A:

Q: The simply supported beam shown below is homogeneous, prismatic and has a distributed axial load of…

A:

Q: Please do parts d, e, and f.

A: Part d, e and f is to be solved

Q: Question Water flows through a 100 mm diameter pipe with a velocity of 0.015 m/sec. If the kinematic…

A: Water flow in a pipe-Pipe diameter d=100 mm,Velocity V=0.015 m/s,kinematic viscosity To Find-The…

Q: Based on the Q1 (a)(i), suggest the method that could potentially provide the best approximation.…

A:

Q: I need some help with part c

A: c. Given Data, RCy=20 N Free body diagram for the figure is given as, tanα=2410α=tan-12.4α=67.3°

Q: The stresses shown act at a point in a stressed body. Normal and shear stress magnitudes acting on…

A:

Q: A three-fluid system (immiscible) is connected to a vacuum pump. The specific gravity values of the…

A: Given- Three fluid systems as shown- Unit weight of water =9.81 kN/m3, Atmospheric pressure = 95.43…

Q: Please do Part C, E, and F

A: To solve part C,E and F

Q: P = 10 1.5P kN- PKN- F 1.5 m, GH -3 m E -3m- 1.5 m, IC -3 m D ++ B 2m 6 m

A: P=10kN To find moment about point A

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as…

A: Given data,  n= 0.013 Discharge, Q= 12 cfs Length of pipe = 160 ft Diameter of pipe = 4 in To find…

Q: SQ1. The bars AB and BC are joined by a pin at A and a horizontal cable. The vertical cable carrying…

A: Free Body Diagram:- tan30 = AB5 AB = 2.887 m sin 30 = xAB x=2.887*sin30 x=1.4435m sin30=y3 y=1.5m…

Q: A sphere of diameter 2 mm falls 150 mm in 20 seconds in a viscous liquid. The density of the sphere…

A: Given data- Diameter of the sphere d=2 mm, Falling distance y=150 mm, Time t=20 s, Density of sphere…

Q: 2. A steel bar, whose cross section is 0.60 inch by 4.10 inches, was tested in tension. An axial…

A: Note :- as per our guidelines we are supposed to answer first three subparts only. Please repost…

Q: The service loads acting on a structural member are as follows: DL = 80 kN/m; WL = 50 kN/m; LL = 40…

A: Given data, To find the limit state of collapse load

Q: do it correctly asap.

A: Given:-m1=1350kgm2=900kgnatural frequencies =4.91Hz and 12.05 HzTo find:-expressions for…

Q: A suppressed rectangular weir in a rectangular channel of width 2.6 m carries a discharge with a…

A: Given - Width, L = 2.6 m Head, H = 0.30 m Coefficient of discharge, cd = 0.63 To find -  Discharge…

Q: SITUATION. In accordance with the Boussinesq Theory, the vertical stress at a point below the center…

A: F (load) = 1500KN D = 4m R (radius) = 2m

Q: Determine the LRFD design strength (kN) of the compression member shown. The distance between the…

A:

Q: Note: Please show all of the free body diagrams used (from reactions and etc.) and also show the…

A:

Q: Q.13 Two reservoirs connected by a pipe of friction factor 'f 'has a difference in water surface…

A: 2 reservoirs connected by a pipe-Friction factor=fDifference in water surface elevations=HH & f…

Construction Process

In civil engineering, construction is the combination of art and science, to construct a physical and naturally built environment, starting from the design phase. The construction process falls under the area of building construction, which is a sub-branch of civil engineering. Hence, it is also sometimes called the design and build or design-build process. The work of construction is majorly carried out by civil engineers and design professionals along with a team of works consisting of contractors and subcontractors.