Suppose that you are making preliminary design calculations for a deep submersible vehicle that is to have a cylindrical hull with hemispherical ends and a 1.5-m radius. At its operating depth, the internal pressure will be 1E5 Pa, and the external pressure will be 330E5 Pa. Choose an aluminum alloy from Appendix B (recommend to use 2014-T6 aluminum alloy the normal yield stress is 410 MPa), and determine the necessary thickness of the hull so that it has a safety factor FS = 2.

Q: ship weight : 200,000 ton 1) Define the type of this problem from the Strength of Materials Point…

A: From the given data;  The given problem is related to the strength of material as it determinesthe…

Q: P2. Design a cylindrical thin-wall composite fuselage for storing compressed natural gas at a…

A:

Q: A piece of cork having a specific weight of 2.36 kN/m 3 is shaped as shown in Fig. 5.32 . (a) To…

A:

Q: The uniform cross-section of a barge with a semi-cylindrical hull floating in water is shown…

A: The buoyant force is the upward force exerted by a fluid when an object is submerged in it. The…

Q: 5 kN 120 9. Way 100 x 200 × 120 mm rubber block in size is placed on the U profile without any gaps…

A: E=12 GPaν=0.5Dimension of way of rubber block=100×200×120 mmF=5 kN

Q: Problem 3 A gate is 1.5m in wi dth and hinged at point A. Another point on the gate, B. is resting…

A:

Q: Calculate the displacement in tonnage for a life buoy with the following characteristics. Di = 0.7 m…

A: The term "displacement tonnage" is used to describe the length of a naval ship. In normal seagoing…

Q: A tank 12 m high and 2 m in diameter is 15 mm thick. The max tangential stress is ? The max…

A: To Find : The maximum tangential stress.The maximum longitudinal stress.Given : The diameter of…

Q: If a spherical balloon is made of an inelastic material that can withstand 395 KN before bursting,…

A:

Q: A project to make a solid cylindrical buoy with its axis vertical was given to you by your company.…

A: Archimedes' principle, or the physical law of buoyancy, states that any body wholly or partially…

Q: (b) A cylindrical tank of outer diameter 3.0 m and wall thickness 20 mm is open at the top as shown…

A: givend=3m=3000mmt=20mmγ=9.81 kN/m3σc=8MPa

Q: A square steel plate is 7.00 cm on a side and 0.600 cm thick. Assume that the plate is oriented with…

A:

Q: The strength of the longitudinal joint is 25 kips/ft, whereas for the girth joint it is 20 kips/ft.…

A:

Q: Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on Pressure…

A: Given data: -  The yield strength of the pressure vessel is σy = 250 MPa. The pressure acting in…

Q: A certain weight of concrete (= = 25 kN/m³) must be attached to the outside bottom of a metal box…

A:

Q: Find the Young’s modulus (Y) of the steel rod of 1 m long and a cross sectional area of 0.05 cm2,…

A: Given data:- The length of the rod                       The cross-sectional area…

Q: Problem :  Pressure vessel made of alloy steel with Yield Strength of 250 MPa, Pressure acting on…

A: Given data: -  The yield strength of the pressure vessel is σy = 250 MPa. The inner diameter of the…

Q: Would a wooden cylinder (s = 0.61) 660mm in diameter and 1.3m long be stable if placed vetically in…

A:

Q: [Stability] A 10-cm by 10-cm wood (sg = 0.65) with a length of 2 m is placed in water. Determine the…

A: Given data  cross-section dimension of wood is 10 cm*10cm the specific gravity of wood (S.G) = 0.65…

Q: A 130 cc block has a piece of lead tied to it. Suppose that the SG of lead is 11.13 and SG of the…

A:

Q: Calculate the minimum wall thickness (in) for a cylindrical vessel that is to carry a gas at a…

A: Pressure(P)=1766 psiDiameter,d=2 ftLimited stress,To determine:Minimum wall thickness(t)

Q: Еxample 02: A raft is constructed of wood having a density of 6.00 × 10² kg/m³. Its surface area is…

A: Given data: ρwood=6×102 kg/m3A=5.7 m2V=0.6 m3 Need to determine the value of "h" of the raft…

Q: A certain cable, 504.76 ft long is suspended between two supports at the same elevation and 500 ft…

A:

Q: The piston rod of an air operated press is to exert a maximum force of 20 kN. During the application…

A:

Q: A cube of steel with sides 2 cm long is placed in a pressure chamber. The pressure is increased…

A: Solution: Given Data: *The side of the cube is: x = 2 cm *The hydrostatic pressure is: P = 1515 kPa

Q: with Diameter of 3 in Cove a and Length of 7 in, with wet weight lbf of 3.44 and porosity of 0.172.…

A:

Q: Applied mechanics: An undersea research vehicle has a spherical hull of 1m radius and a 40mm…

A: Radius r = 1m Thickness = 40mm High strength alloy steel  yield point =700MPa Relative density of…

Q: You have the thin walled pressure vessel shown. Given

A: Given that ,  Inner radius Ri=3.00ftWall thickness t=0.25in =0.020833 ft Length L=10 ft

Q: Problem 2. The plan is to frac a stratum at 8500 ft having a fracture pressure of 4,200 psig. Solve…

A:

Q: A thick-walled cylinder has an outer and inner diameter of 200 and 50 mm, respectively. The…

A:

Q: The steel plate has the dimensions shown. Determine the maximum axial force P that can be applied so…

A: Given Maximum allowable stress = 21 ksi  r= 0.25 in d = 1 in t = 0.25 in w= 5 in D = 2.52 in To find…

Q: A cylinder is made of steel palte is intended to be used as a container for compressed air. The…

A:

Q: When rebuilding his car's engine, a mechanic must exert 300'N of force to insert a dry steel piston…

A:

Q: In the figure shown below, the deflection of mercury is initially   250mm . If the pressure at A is…

A: Given: Initial deflection of mercury =250 mm=0.25 m The pressure at A is increased by PA'=33 kPa

Q: 5. The gas tank (inner diameter 1.5 m) is made from steel which has a yield strength of 250 MPa. If…

A:

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.