Suppose that the fatigue data shown in the Animated Figure: S-N Plot for Steel is for a steel alloy that was tested using bending- rotating tests. A rod of this alloy is to be used for an automobile axle that rotates at an average rotational velocity of 1000 revolutions per minute. Give the maximum lifetimes of continuous driving that are allowable for the following stress levels: (a) 450 MPa i (b) 380 MPa i (c) 310 MPa i hours hours hours

Suppose that the fatigue data shown in the Animated Figure: S-N Plot for Steel is for a steel alloy that was tested using bending- rotating tests. A rod of this alloy is to be used for an automobile axle that rotates at an average rotational velocity of 1000 revolutions per minute. Give the maximum lifetimes of continuous driving that are allowable for the following stress levels: (a) 450 MPa i (b) 380 MPa i (c) 310 MPa i hours hours hours

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Calculate a diameter, d, to ensure that yield does not occur in the 1045 carbon steel (Yield stress = 310 MPa) under 220kN tensile load. Use a factor of safety of 5.
kindly help me with this problem choose the correct answer
Using the relationship θ = TL / IpG in the above problem, again determine the diameter that is necessary to satisfy the requirement of rigidity (remembering to convert θ from degrees to radians). Considering the strength and rigidity requirements, which diameter should we choose
I need a clear answer by hand, not by keyboard and fast answer within 20 minutes. Thank you | dybala
Derive the following equation for computing shear stress in a solid bar along an oblique plane with angle B with respect to the vertical plane. The bar is subjected to centric axial loading. sin 0 cos 0 T = Ao
PLEASE ANSWER NUMBER 3.MECH 222-MECHANICS OF DEFORMABLE BODIES: PLEASE GIVE DETAILED SOLUTIONS AND CORRECT ANSWERS. I WILL REPORT TO BARTLEBY THOSE TUTORS WHO WILL GIVE INCORRECT ANSWERS.
A tensile-testing apparatus is to be constructed that must withstand a maximum load of 293516 N. The design calls for two cylindrical support posts, each of which is to support half of the maximum load. Furthermore, plain-carbon(1045) steel ground and polished shafting rounds are to be used; the minimum yield and tensile strengths of this alloy are 343 MPa and 565 MPa(82,000 psi), respectively. Specify a suitable diameter in mm for these support posts. Assume safety level is 2.3. Round your answer to 2 significant figures.
Calculate the ductility of this steel alloy in %EL.
Please do it typed not handwriting. Make sure the answer is correct Don't copy from any other online answers please
2. The diameter of a bar fabricated from an alloy with properties shown in figure below reduced from an initial 1.2 in. to a 1.0 in. diameter, to a final 0.8 in. diameter. For parts a, b, and c; when using the graph, you can ignore the marked points A, B, C, and O (a) Determine the % CW after the first step of the process (b) Determine the yield stress (in ksl) after the first step. of the process (c) Determine the % CW after the second step of the process 22 Tensile strength (ksi) 20 18 Yield strength (ksi) 16 14 12 10 Elongation (%) 4 2 20 40 60 80 Property
Question 1 The S-N diagram for a titanium alloy is shown in the figure. Calculate the fraction of life consumed by the following sequence of loadings: 15,000 cycles at 80 MPa 120,000 cycles at 60 MPa 3,500,000 cycles at 50 MPa Maximum stress (ksi) 160 140 120 100 80 60 40 20 I 10³ 104 105 Cycles to failure 100 107