Suppose a liquid has a specific gravity of 6.28. If the measured pressure at the bottom of the tank in which it is stored is 83.58 psi, what is the height of the liquid in feet.

Q: The figure below shows a closed container holding water and oil. Air at 35 kPa below atmospheric…

A: Given: The air pressure inside the closed container is -34 kPa. The specific gravity of oil is 0.85.

Q: A pressure gauge fitted on the side of a tank filled with liquid reads 50 kPa and 100 kPa at heights…

A:

Q: Consider oil flowing through a horizontal pipe at a rate of 3 liter/s. There are two sections of the…

A:

Q: PROBLEM 1: Both a gage and a manometer are attached to a tank to measure pressure. Given the reading…

A:

Q: Calculate the pressure difference between the water pipe (point A) and the oil pipe (point B) that…

A:

Q: Fluid Mechanics question: As shown in the image, an air space above a long tube is pressurized to 50…

A: Consider the unit weight of water is 9790 N/m3Consider a point 1 on the surface of reservoir and…

Q: Water 8 cm 2 cm - Hg 4 cm Hg- 2 cm Water

A:

Q: For water, starting with 1 m3 of water in a container, what is the pressure required to decrease the…

A: Given: The volume of water is 1 m3. The decrease in volume of water is 1%.

Q: Meriam red oil, SG=0.827 P2.32 Water A 18 cm H 35 cm B Mercury

A: Given data:- The PB-PA=89.5 kPa=89500 Pa The specific weight of water is, Wwater=9790 N/m3 The…

Q: Determine the distance between the two fluid levels of the manometer if the fluid is mercury (p =…

A: Answer Equate the pressure on both the sides taking datum as shown in black line below  gage…

Q: A pressure gauge fitted on the side of a tank filled with liquid reads 50 kPa and 100 kPa at heights…

A: given- pressure PA=50 kPa at 5 mpressure PB=100 kPa at 10 mg=10 m/s2

Q: Problem 1. A manometer is first filled with water (blue) and then with mercury (gray). The mercury…

A: To find pressure at point a

Q: 1. The pressure in an automobile tire depends on the temperature of the air in the tire air…

A:

Q: PROBLEM 4: The tank contains a liquid having a density as shown. 0.82 ft 10 ft 5 ft 7 ft Pliquid =…

A: (a) multiplying the density by "g" acceleration due to gravity  to obtain the unit weight Unit…

Q: In a manometer shown in Fig.1, the fluid from A to B is mercury (sp. gravity 13.6) and from B to C,…

A: Given: The specific gravity of the mercury is 13.6. The specific gravity of the oil is 0.80. The…

Q: The outside diameter of a right circular cylindrical tank is 3,000 mm and its height is 6,000 mm. If…

A:

Q: 5.5 in. Open 1.4 in. Water Unknown fluid Open 4.9 in. 3.3 in.

A:

Q: A tank contains gasoline and glycerine with open piezometer tubes attached as shown. The depths of…

A:

Q: 1) Ifa depth of liquid of 1 m causes a pressure of 7 kPa, what is the specific gravity of the…

A: per our company guidelines we are supposed to answer only first 3 sub-parts. Kindly repost other…

Q: Q2:- The pressure of the gas corresponding to various volumes V is measured, given by the following…

A:

Q: 3. A student wants to find the absolute pressure of water at a point below the surface of water. He…

A:

Q: PROBLEM 5: The water in a tank is pressurized by air, and the pressure is 4 points measured by a…

A:

Q: 1. For the computation of density of liquids to be tested, use the following values of density of…

A:

Q: 2 The tank shown contains air, oil, and water. Gage A reads 100 kPa and Gage C reads 16.872 kPa more…

A:

Q: The figure below shows a closed tank that contains gasoline floating on water. Calculate the air…

A: Solution: Given Data S.G for mercury=13.54  Pressure is given byP=ρghρ=density of…

Q: A pressure gauge at elevation 12m at the side of a tank containing a liquid reads 80 kPa. Another…

A:

Q: An average table tennis ball has a diameter of 3.817 cm. and a mass of 2.674 grams. Assuming that…

A: The given data is as follows: Diameter of tennis ball=3.817 cmMass of ball=2.674 gramsDepth of…

Q: Three different liquids can be found in the tank as shown in the figure. Determine the pressure…

A:

Q: Three different fluids, water, oil (SG = 0.83), and unknown fluid, fill the tank and manometer tube…

A:

Q: The water in a tank is pressurized by air, and the pressure is measured by a multifluid manometer as…

A:

Q: A cylindrical object 82mm diameter, 165mm height and a mass of 599g, is placed in the tank, which…

A: Given data, Diameter of object d = 82 mm Height of object h = 165 mm Mass of object m = 599 g…

Q: For the given figure, determine the gage pressure at the oil surface A in Pascal unit. Write your…

A:

Q: Water A H1 cm H2 cm Mercury

A:

Q: Q/ The laminar flow of water through a pipe is measured by means of a pitot tube situated in the…

A: When the manometer is connected to pitot tube - reading = x1 = 100mm or .1m Difference in pressure…

Q: A vacuum gauge connected to a tank reads 30.0 kPa. If the local atmospheric pressure is 13.5 psi,…

A:

Q: A manometer consists of a tube of 0.5 inch in the inner diameter and an amount of mercury (SG Hg…

A: To determine how much the mercury height rises (h4 - h2), we can use the principles of fluid…

Quantity takeoff

Quantity takeoffs (QTO) are precise estimates of the materials and labor costs required to finish a construction project. During the pre-construction phase, an estimator prepares them, breaking down the project into smaller, more manageable parts that are easier to evaluate. These measurements are used to prepare a construction scope bid. Estimators examine the drawings, specifications, and models to figure out different quantities and their costs. Since, the components, their quantity, and price are all included in the model, quantity take-off can be done automatically using Building Information Modelling (BIM). The time taken for completing a construction project can be reduced by the use of quantity takeoff. These takeoffs are also called material takeoffs and construction takeoffs.