Suppose a file of 10,000 bytes is to be sent over a line at 2400 bps. A. Calculate the overhead in bits and time in using asynchronous communication. Assume one start bit and a stop element of length one bit, and 8 bits to send the byte itself for each character. The 8-bit character consists of all data bits, with no parity bit. B. Calculate the overhead in bits and time using synchronous communication. Assume that the data are sent in frames. Each frame consists of 1000 characters = 8000 bits and an overhead of 48 control bits per frame. C. What would the answers to parts (a) and (b) be for a file of 100,000 characters?

Suppose a file of 10,000 bytes is to be sent over a line at 2400 bps. A. Calculate the overhead in bits and time in using asynchronous communication. Assume one start bit and a stop element of length one bit, and 8 bits to send the byte itself for each character. The 8-bit character consists of all data bits, with no parity bit. B. Calculate the overhead in bits and time using synchronous communication. Assume that the data are sent in frames. Each frame consists of 1000 characters = 8000 bits and an overhead of 48 control bits per frame. C. What would the answers to parts (a) and (b) be for a file of 100,000 characters?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Similar questions

[8.3] Calculate by hand 8.625 × 10¹ divided by -4.875 x 10°. Show all the steps necessary to achieve your answer. Assume there is a guard, a round bit, and a sticky bit, and use them if necessary. Write the final answer in both the 16-bit floating-point format (1 for sign bit, 5 for exponent, and 10 for fraction) and in decimal and compare the decimal result to that which you get if you use a calculator.
Assume a fixed priority scheme where Processor3> Processor2 > Processor1. Processor3 makes a request and is granted access. Then, Processor2 and Processor1 make requests. Which processor is granted access first? O Processor 1. Processor2 O Processor3 O An error will occur because two requests are pending
Is there a reason why the duration between bytes in asynchronous transmission varies?
Suppose a file of 10,000 bytes is to be sent over a line at 2400 bps. A. Calculate the overhead in bits and time in using asynchronous communication. Assume one start bit and a stop element of length one bit, and 8 bits to send the byte itself for each character. The 8-bit character consists of all data bits, with no parity bit. B. Calculate the overhead in bits and time using synchronous communication. Assume that the data are sent in frames. Each frame consists of 1000 characters = 8000 bits and an overhead of 48 control bits per frame. C. What would the answers to parts (a) and (b) be for a file of 100,000 characters?
Consider a hypothetical 8 bit floating point machine representation with a sign bit, a 3 bit exponent, and a 4 bit mantissa (se1e2e3b1b2b3b4), where the exponent bias is 3 (add 3 to exponent of number to form machine representation). Recall that actual mantissa has 5 bits, since the leading 1 is not stored on the machine. (a) What is the number ?≈2.718 in this 8-bit format? (b) What is the number that (10100111)2 represents in this 8-bit format? (c) What is the upper bound of the relative error when representing a real number in this 8-bit format?
In a Von Neumann architecture, groups of bits have no intrinsic meanings by themselves. What a bit pattern represents depends entirely on how it is used. The following table shows bit patterns expressed in hexadecimal notation i. 0x000940C2 ii. 0x8C90FFFC Qa)What decimal number does each bit pattern represent if, i.It is a two’s-complement integer? ii.It is an unsigned integer? b) If each bit pattern represents an MIPS instruction, what instruction will be executed? c) What decimal number does each bit pattern represent if it is a floating-point number in IEEE 754 standard?
1. Suppose you have the following 2 bytes: 01011100 and 01100101. What is the 1s complement of the sum of these 2 bytes? 2. Suppose you have the following 2 bytes: 11011010 and 01100101. What is the 1s complement of the sum of these 2 bytes? 3.. For the bytes in part (a), give an example where one bit is flipped in each of the 2 bytes and yet the 1s complement doesn' t change.
The figure below illustrates an asynchronous transmission in the form of short blocks. Each data bit is of 9.06 ms duration, start bit duration is 0.04ms more than a data bit duration, and each stop bit duration is double the duration of a start bit . Determine the bit rate and baud rate of the transmission. Data Bits Stop Bits Start Bit 1 101 0 10 010 1 Line is quiet! Direction of Data Data: 0100 1010
The following paging system has 64KB main memory, which is divided into 16 frames (frame numbers are from 0 to 15). Suppose the process A has 4 pages. The page numbers are 0, 1, 2, and 3, which are loaded to frame 9, 0, 1, and 14, respectively. What is the length of process A? (ii) For logical addresses 0001 0000 0100 1000 and 0011 0000 0110 0011 (all logical addresses are binary values), convert them to the physical address in the main memory.
internet Checksum. Consider the two sixteen bit numbers: 10110100 01000110 00001000 01101110 Compute the Internet Checksum of these two values Enter the 2 bytes each as an 8-bit number with only O's and 1's, and make a single blank space between the two 8-bit numbers (e.g., 01010101 00101000).
1) Assume that we would like to transmit a file of size 2 Gbits. The modulator uses the baseband waveform ø1(t) = sinc -) with a bandwidth of 1 MHz and the encoder uses either BPSK or 4-PAM. How long does it take to complete transmission of the file (assuming that there are no errors)?
Internet Checksum. Consider the six sixteen bit numbers: 10110101 01000110 01001001 01101011 10110100 01000110 01001001 01101101 10110101 01010110 01011010 01101111 Compute the Internet Checksum field value of these six words (each word has sixteen bits) Enter the 2 bytes each as an 8-bit number with only O's and 1's, and make a single blank space between the two 8-bit numbers (e.g., 01010101 00101000). [Note: you must use bitwise XOR logic function and don't use 2's or 1's complement] Not quite. This answer is incorrect.