Supercomp Ltd produces two computer models PC1086 and PC1186. The matrix A shows the cost per computer (in thousands of dollars) and B the production figures for the year 2010 (in multiples of 10,000 units.) Find a matrix C that shows the shareholders the cost per quarter (in millions of dollars) for raw material, labor, and miscellaneous. Quarter 1 2 3 4 PC1086 PC186 1.2 1.6 Raw Components 3 8 6 9 B PC1086 0.3 0.4 Labor 6 2 4 3 PC1186 0.5 0.6 Miscellaneous

Supercomp Ltd produces two computer models PC1086 and PC1186. The matrix A shows the cost per computer (in thousands of dollars) and B the production figures for the year 2010 (in multiples of 10,000 units.) Find a matrix C that shows the shareholders the cost per quarter (in millions of dollars) for raw material, labor, and miscellaneous. Quarter 1 2 3 4 PC1086 PC186 1.2 1.6 Raw Components 3 8 6 9 B PC1086 0.3 0.4 Labor 6 2 4 3 PC1186 0.5 0.6 Miscellaneous

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

760 ۱۲:۳۱ Note: Answer All The Questions. Moody Chart is allowable. 01) Select the most suitable complement among listed options for the 10 items: 1) Real fluids (a) are viscous (b) possess surface tension (c) are compressible (d) possess all the above properties (e) possess none of the above properties. 2) In a static fluid (a) resistance to shear stress. small (b) fluid pressure is zero (c) linear deformation is small (e) viscosity is nil. (d) only normal stresses can exist 3) When the flow parameters at any given instant remain same at every point, then flow is said to be (d) uniform (e) Static. (a) Turbulent (b) Steady state (c) laminar 4) The increase of temperature results in (a) increase in viscosity of gas viscosity of gas (b) increase in viscosity of liquid (c)decrease (e) (a) and (d) above. d (d) decrease in viscosity of liquid 5) Consider the flow in pipe in figure. If P₁ -AP/y. b) The flow direction is from 2 to 1 if AZ <-AP/y. c) The flow is zero if AZ=-AP/y. d) The flow…
Please show me the full solution so I will know how to solve it, thank you very much.
production planning and control help please
Q8): To find how much heat is required to bring a kettle of water to its boiling point, you are asked to calculate the specific heat of water at 61°C. The specific heat of water is given as a function of time in Table below. Temperature, T Specific heat, C₂ (°C) J kg-°C 22 42 52 82 100 4181 4179 4186 4199 4217 Determine the value of the specific heat at 7=61°C using the direct T method of interpolation and a third order polynomial. Find the absolute relative approximate error for the third order polynomial approximation (Lagrange Method).
16000 1.440 14000 1.435 12000 1.430 10000 1.425 8000 1.420 6000 1.415 4000 1.410 2000 1.405 1.400 45 15 20 25 30 35 40 Temperature ["C] +dynamic viscosity (mPas] + density (gicm") Figure 1 (a) As shown in Figure 1, viscosity and density of honey was found to decrease with increase in temperature. Explain the reasons behind these phenomenon related to Fluid Mechanics in microscopic view. Dynamic viscolsty [mPa.s] Density [g/cm³]
The traffic volume data table below counts was taken on rural a highway during the morning peak hour at (8:00-9:00 am) on Monday of a week. Time periods (minute) 8:00-8:15 AM 8:30-9:00 AM Number of vehicles 385 790 The average time headway (sec) during 8:00-9:00 am 2.25 a) Find the traffic volume for the period from 8:15 to 8:30 am. b) Determine the hourly volume (HV), the maximum rate of flow within the hour, and the peak hour factor (PHF). c) Estimate the density and speed of traffic if an average spacing of 150 ft. d) Estimate the daily volume for Monday if the hourly expansion factor (HEF) is 22.05.
Answer the following question and explain
Please solve this
I need help with parts d, e, and f please.
Please give correct answers
We have a cylinder 25 cm in diameter fitted with a rod 5 cm in diameter.diameter and subjected to a pressure of 200 kPa?a) Calculate the effective area of thrust. [Answer:0.049 m2]b) Calculate the effective area of traction. [Answer:0.047 m2]c) Calculate the thrust force of the jack. [Answer:9800N]