Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a diameter of 35 mm. If the acid flow rate is 1 m3 / min, what is the pressure loss due to friction in a 40 m long smooth pipe? a. Reynold number = Answer. b. Loss of Pressure = Answer kPa.

Q: What are the liquid and vapor flow rates for the bottom and distillate streams

A:

Q: width and 5 m A horizontal square wooden rod, 2 m long. 0.2 m head width is hung and fixed at the…

A:

Q: Water flows in a pipeline composed of 75 mm and 150 mm pipe. Calculate the mean velocity in the 75…

A:

Q: While attempting to extinguish a fire, firefighters are holding a nozzle at the end of a hose. If…

A:

Q: The tank below is cylindrical and has a vertical axis. Its horizontal cross-sectional area is 10 m2.…

A: The schematic labeled diagram for the given system is shown below as:   Given information:   The…

Q: Consider the flow of a fluid through the piping system shown below in Figure 1. Flow If D₁ = 4D2,…

A:

Q: My sister and I can play tennis. quite well not at all a littie bit I read . one lecture the O none…

A:

Q: air h, h, water

A: Given Density of water ρw =1000 kg/m3 h1 = 60 cm h = 45 cm h2 = 180 cm Find-Difference of…

Q: Q3) Water flows through a 10-mm diameter pipe at a flow rate of 1.33×104 m³/s. Find (a) Velocity (V)…

A: As water is flowing through the pipe with a flow rate of Q. Reynold's number is the dimensionless…

Q: Q.3) The gage pressure of the air in the tank shown in Figure below is measured to be 80 kPa.…

A:

Q: mooth inner surface for

A:

Q: 17. Calculate the pressure at point A in Fig. 2.50. The slope of the tube is 4 horizontal to 1…

A: Reservoir review is given.Calculate pressure at point A.

Q: The initial free fall of water from a faucet can be thought of as an inviscid flow because friction…

A: Given: The distance between points 1 and 2 is 7 cm i.e. z1 - z2 = 7 cm or 0.07 m The diameter of…

Q: Water at 30°C is being pumped through a 30 m section of 19.49 cm. diameter steel pipe at a mass flow…

A: Given data: Length of the pipe = 30 m Diameter of pipe = 19.49 cm Mass flow rate = 0.07 kg/s Density…

Q: 33. Viscous flow in a plunger-M. A tube of diameter D = 2.0 cm and length L = 100 cm is initially…

A: Given data: Diameter of tube = 2 cm Length = 100 cm Density of the fluid = 1 g/cm3 Viscosity of the…

Q: A simple batch distillation without reflux is ran until 30% of the initial feed is taken off as…

A:

Q: The wastewater treatment process at a polymer plant consists of a longitudinal bio-remediation pond…

A:

Q: Sulphuric acid is flowing through a pipe (2.5 inch diameter, 50 ft length) in a velocity of 0.006 m3…

A: Given: diameter D = 2.5 inch = 0.0635 m, A = pi.D2/4 = 0.003165 m2 Thus, V = Q/A = 0.006/0.003165  =…

Q: parallel piping hor. plane. pipe consists of two pipelines, i.e. Pipe 1 and Pipe 2. Pipe 1 is 60 m…

A: As per Bernoulli's equation applied between points A and B,PAγ+VA22g+ZA=PBγ+VB22g+ZB+hL1Neglecting…

Q: The following are the cooling water requirements for a process industry: Heat exchanger 1: 300 m³…

A: Given that : Heat exchanger volumetric flow rate(m^3/hr) density (Kg/m3) x106 1 300 3 2 150…

Q: P.4.14 Water (density 1000 kg/m', viscosity 1 mNs/m²) is pumped through a 50 mm diameter pipeline at…

A: Case 1: Flow of water through pipe Mass flow rate of water, mW = 4 kg/s Diameter of the pipe, d = 80…

Q: Water at 30°C is being pumped through the annular area of a laboratory scale 1-pass, 1-shell tube…

A: Volumetric flow rate of water = 0.1 m3/s Inside diameter of the shell, d2 = 18.4 cm Outside diameter…

Q: Q2: A 60 mm diameter pipe contains glycerin (sp.gr 1.258) flowing at 8.5 m'/hr as shown in the…

A: Given: d = 60 mm, specific gravity = 1.258, Q = 8.5 m3/hr and zA = 0m, zB = 12 m. PA = 2 atm and PB…

Q: Water is flowing through a 30-m-long and 5-cm-diameter horizontal pipe at a rate of 9 L/s. Using…

A: We are given that  Length= L = 30 m diameter=d = 5 cm =0.05 m flow rate = Q = 9 L/s = 0.009 m3/s…

Q: If the natural gas flow rate is 120 MMSCF/Day in a gas pipeline, NPS 20 with 0.25 in wall thickness,…

A: To calculate the outlet pressure using the Panhandle A equation, we can use the following…

Q: 2) Both ends of the nozzle with an inlet cross-sectional area of lx10-S ft² and an outlet cross-…

A: In fluid mechanics, Bernoulli's theorem is described as the total mechanical energy of the flowing…

Q: 0.4 m 0.4 m 0.5 m 1.0 m water s 0.90 oil, s=

A: Solution Given that different fluids with specific gravity One atmosphere (101.325 kPa) is also the…

Q: The flow behavior of a polymer melt with a specific gravity of 1.17 and a viscosity of 0.486…

A:

Units and Dimensions

Dimensions are the basic concepts of the measurement of quantities. Units are the means of expressing the dimensions. For instance, an area has a dimension of L2 and a unit of m2.