Sulfuric acid with a density of 1980 kg / m3 and a viscosity of 26.7 cP flows in a pipe with a diameter of 35 mm. If the flow rate of the acid is 1.55 m / min, what is the pressure loss due to friction in a 30 m long smooth pipe? a. Reynold number = b. Pressure Loss= kPa

Q: width and 5 m A horizontal square wooden rod, 2 m long. 0.2 m head width is hung and fixed at the…

A:

Q: Water flows in a pipeline composed of 75 mm and 150 mm pipe. Calculate the mean velocity in the 75…

A:

Q: air h, h, water

A: Given Density of water ρw =1000 kg/m3 h1 = 60 cm h = 45 cm h2 = 180 cm Find-Difference of…

Q: Q3) Water flows through a 10-mm diameter pipe at a flow rate of 1.33×104 m³/s. Find (a) Velocity (V)…

A: As water is flowing through the pipe with a flow rate of Q. Reynold's number is the dimensionless…

Q: Q.3) The gage pressure of the air in the tank shown in Figure below is measured to be 80 kPa.…

A:

Q: Water is flowing through a 30-m-long and 5-cm-diameter horizontal pipe at a rate of 9 L/s. Using…

A:

Q: Probem: A liquid at 293 K flow at a the rate of 0.7 kg/s in a glass pipe having a diameter of 64 mm.…

A:

Q: Oxygen in the air is traveling at an average speed of 444 m/s. If the coefficient of viscosity is…

A: Given that, Average Speed of Oxygen vavg = 444 msCoefficient of viscosity μ = 175 micropoise = 175 ×…

Q: 17. Calculate the pressure at point A in Fig. 2.50. The slope of the tube is 4 horizontal to 1…

A: Reservoir review is given.Calculate pressure at point A.

Q: A liquid flows through a horizontal straight commercial steel pipe 30.48m long and a pipe roughness…

A: Given density=ρ=1200kg/m3 viscosity=μ=0.01kg/m.s Pipe roughnes=e =0.045 mm = 0.045 × 10-3 m Length…

Q: Sulfuric acid with a density of 1500 kg/m3 and a viscosity of 22.5 cP is flowing in a 32 mm diameter…

A: Given:density, ρ=1500kgm3viscosity, μ=22.5 cP=22.5×10-3kgm.sDiameter of pipe, D=32 mm=32×10-3…

Q: An open container is filled with water up to a depth of 3 meters and above water it is filled with…

A: As per the given information, the tank is filled with oil and water as shown in Figure1.Density of…

Q: Question 3 The average volumetric flow through an open rectangular duct can be estimated using the…

A:

Q: Water at 30°C is being pumped through a 30 m section of 19.49 cm. diameter steel pipe at a mass flow…

A: Given data: Length of the pipe = 30 m Diameter of pipe = 19.49 cm Mass flow rate = 0.07 kg/s Density…

Q: 33. Viscous flow in a plunger-M. A tube of diameter D = 2.0 cm and length L = 100 cm is initially…

A: Given data: Diameter of tube = 2 cm Length = 100 cm Density of the fluid = 1 g/cm3 Viscosity of the…

Q: Show illustration of a large, open cylindrical tank is 18ft deep having a radius of 7ft is layered…

A: This is a problem of fluid statics and comprises of three materials:   Mercury Water Oil We will…

Q: Water at 20°C flows in a cylindrical pipe with internal diameter of 2 cm. At what critical fluid…

A:

Q: A straight pipe with an expansion in pipe from 6 to 11 cm transports water at a rate of 0.011 m /s.…

A:

Q: 10. Consider a system with a * pitot tube (with a U-tube manometer) attached to a horizontal oil…

A: Given S.G=0.84 μ=0.05 kg/m-sec ID=0.11 yard h=0.42 yard Find Volumetric flow rate,Q

Q: 1. What is the net force acting on a car cruising at a constant velocity of 70 km/h (a) on a level…

A: Given that  constant velocity = 70 km/h  we have to find the net force acting on a car cruising on a…

Q: 5.1-2. Frictional Pressure Drop in a Flow of Olive Oil. Calculate the frictional pressure drop in…

A: Olive oil density and viscosity at a given temperature are obtained. The Reynolds number is…

Q: The wastewater treatment process at a polymer plant consists of a longitudinal bio-remediation pond…

A:

Q: Sulphuric acid is flowing through a pipe (2.5 inch diameter, 50 ft length) in a velocity of 0.006 m3…

A: Given: diameter D = 2.5 inch = 0.0635 m, A = pi.D2/4 = 0.003165 m2 Thus, V = Q/A = 0.006/0.003165  =…

Q: parallel piping hor. plane. pipe consists of two pipelines, i.e. Pipe 1 and Pipe 2. Pipe 1 is 60 m…

A: As per Bernoulli's equation applied between points A and B,PAγ+VA22g+ZA=PBγ+VB22g+ZB+hL1Neglecting…

Q: P.4.14 Water (density 1000 kg/m', viscosity 1 mNs/m²) is pumped through a 50 mm diameter pipeline at…

A: Case 1: Flow of water through pipe Mass flow rate of water, mW = 4 kg/s Diameter of the pipe, d = 80…

Q: Water at 30°C is being pumped through the annular area of a laboratory scale 1-pass, 1-shell tube…

A: Volumetric flow rate of water = 0.1 m3/s Inside diameter of the shell, d2 = 18.4 cm Outside diameter…

Q: 2. Air flows from left to right through a duct with a constriction in the middle as shown below.…

A:

Q: Repeat problem 9.13 for the case where the fluid is water at 15°C, assuming the Reynolds number…

A: Note: Since we are entitled to answer only 3 subparts, we’ll answer the first 3. Please resubmit…

Q: Water -Bo C CC14 D 2B.9 Analysis of a capillary flow meter. Determine the rate of flow (in lb/hr)…

A: Diameter of the capillary = 0.01 in Density of the manometric fluid, CCl4 = 1.594 g/cm3

Q: 6. Compute the hydrostatic pressure (psi) that a drilling mud with relative density equals 1.4…

A: The hydrostatic pressure exerted by a fluid at a certain depth is given by the formula: P = ρgh…

Q: A jet of water flows from a 4-in diameter nozzle such that the velocity at point 1, the top of the…

A: Given Data; Steady Flow Diameter of Nozzle; D1 = 4 inches=0.1016 m Diameter of Pipe; D2= 6 inches=…

Q: Water is flowing through a 30-m-long and 5-cm-diameter horizontal pipe at a rate of 9 L/s. Using…

A: We are given that  Length= L = 30 m diameter=d = 5 cm =0.05 m flow rate = Q = 9 L/s = 0.009 m3/s…

Q: 0.4 m 0.4 m 0.5 m 1.0 m water s 0.90 oil, s=

A: Solution Given that different fluids with specific gravity One atmosphere (101.325 kPa) is also the…

Q: 5.1-3. Frictional Loss in Straight Pipe and the Effect of a Type of Pipe. A liquid having a density…

A: Given data: Density; ρ=801 kg/m3Viscosity;μ=1.49×10-3 Pa·sVelocity; V=4.57 m/sDiameter; D=0.0483 m…

Q: The flow behavior of a polymer melt with a specific gravity of 1.17 and a viscosity of 0.486…

A:

Q: In fully developed laminar flow in a circular pipe, the velocity at R/2 (midway between the wall…

A: Consider a fluid element with length dL Now take force balance as shown in figure

Units and Dimensions

Dimensions are the basic concepts of the measurement of quantities. Units are the means of expressing the dimensions. For instance, an area has a dimension of L2 and a unit of m2.