Sublimation is preferred for small scale purification as compared to crystallization because there is little loss of material during transfer True, sublimation guarantees a 100% yield False, the crystallization process is better because it yields a much purer product especially in small scale purification processes True, sublimation has less loss of material because the process has no intermediate liquid stage False, sublimation is better for large scale purification processes.

Sublimation is preferred for small scale purification as compared to crystallization because there is little loss of material during transfer True, sublimation guarantees a 100% yield False, the crystallization process is better because it yields a much purer product especially in small scale purification processes True, sublimation has less loss of material because the process has no intermediate liquid stage False, sublimation is better for large scale purification processes.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Suppose that you have a 1:1 mixture of compounds that is comprised of compound X and compound Y. You desire pure compound X and are planning a recrystallization to enhance the purity. Which solvent below is optimal for your recrystallization? Ethanol (boiling point = 78 °C) Solubility At 0 °C 100 °C Compound X 0.05 g/mL 0.20 g/mL Compound Y 0.02 g/mL 0.40 g/mL Water (boiling point = 100 °C) Solubility At 0 °C 100 °C Compound X 0.02 g/mL 0.05 g/mL Compound Y 0.01 g/mL 0.10 g/mL Methanol (boiling point = 65 °C) Solubility At 0 °C 65 °C Compound X 0.04 g/mL 0.10 g/mL Compound Y 0.02 g/mL 0.30 g/mL Acetone (boiling point = 56 °C) Solubility At 0 °C 56 °C Compound X 0.10 g/mL 0.50 g/mL Compound Y 0.20 g/mL 0.50 g/mL Ethyl Acetate (boiling point = 77 °C) Solubility At 0 °C 77 °C Compound X 0.10 g/mL 0.60 g/mL Compound Y 0.30 g/mL 0.60…
for effective purification by recrystalization while avoiding performing a hot gravity filtration, what is the desired solubility of an impurity at different temperatures? Hot solvent solvent after cooling
The experimental data in the table was collected during a freezing point depression study where BHT (butylated hydroxytoluene) was the solvent. Mass of BHT Mass of unknown Freezing point of pure BHT Freezing point of BHT and unknown solution Kf for BHT 7.709 g7.709 g 1.252 g1.252 g 74.17 ∘C74.17 ∘C 70.91 ∘C70.91 ∘C 6.83 ∘C/?6.83 ∘C/m Use this data to calculate the molar mass of the unknown solute. molar mass =
a. b. C. How are fractional distillation and steam distillation similar? How are fractional distillation and steam distillation different? Kabing works as a The vapor pressure of benzaldehyde at 97 °C is about 60 mm Hg. Assume atmospheric pressure is 760 mm Hg. If you collected 20 g of distillate from your steam distillation, how much of it was benzaldehyde? Show your calculation. (MW)APA =gA (MW)BPB gв
1a. Use the given table to construct a temperature-composition diagram for cyclohexane Toluene mixture. Based on the plot, what is the composition of the distillate obtained by Simple distillation 20 mole percent cyclohexene and 80 mole percent toluene? Show your Work on the plot. 1b. Estimate the composition of the distillate of 20 mole percent of cyclohexane if the Distillation column had three theoretical plates.
The liquid-liquid extraction technique takes advantage of the solubility difference of a given compound in two immiscible solvents. Group of answer choices True False
3. A pure white crystalline compound was found to melt at 131.5-132.0°C when taken on a melting point apparatus, and on further heating, the liquid was found to start bubbling at ca. 155-160 °C. The capillary containing the melted compound was set aside to cool, and resolidify. When the sample was retried using that same capillary, the sample melted at 120.6-154.5°C, along with some bubbling. What is the cause of the bubbles? Why is the melting point so wide the second time? Explain by stating what you have learned in this laboratory about melting points.
True/False
You are attempting to purify a compound via recrystallization. You prepare the process through the following method: 1) Dissolve the material in a minimal amount of hot EtOH. 2) Slowly add hot water until the compound is slightly cloudy. 3) Add a small amount of EtOH until the solution is just clear (still hot). 4) Cool to RT. Upon cooling to RT you notice that the compound is not precipitating out of solution. You decide to boil off some ethanol. Upon completing this step and cooling to RT you notice that the compound is precipitating out as desired! In which solvent is your compound the least soluble? Ethanol O Water O The ethanol water mixture Insoluble in all of these solvents
Based on the melting point of your impure solid, you look at the given samples and believe you havecompound A. Compound A is recrystallized using a mixed solvent system of ethanol and water. You add1 ml of hot ethanol to your sample and it doesn’t completely dissolve. You continue to add hot ethanolbut there isn’t any change. Some solid remains. What should you do next?
Only water or dilute aqueous solution or non toxic chemicals may be disposed of down the drain with copious water true false
Explain why one would recrystallize a solid from a solvent pair instead of a single solvent. Explain how it works in terms of solubilities. please give detail, will only rate if sufficent detail is given. thank you!