Su 300 L/sn 175 kPa 160 kPa . A sprayer elbow is used to throw water at a flow rate of 300 L/sec from a horizontal pipe by deflecting it upwards at an angle of 0=45° and accelerating it. The diameters at the inlet and outlet. are 30 cm and 15 cm, respectively. The pressure is 175 kPa at the inlet and 160 kPa at the outlet. Determine the force that will be exerted on the elbow. Assume the elbow is in the horizontal plane. pwater=1000kg/m3.

Su 300 L/sn 175 kPa 160 kPa . A sprayer elbow is used to throw water at a flow rate of 300 L/sec from a horizontal pipe by deflecting it upwards at an angle of 0=45° and accelerating it. The diameters at the inlet and outlet. are 30 cm and 15 cm, respectively. The pressure is 175 kPa at the inlet and 160 kPa at the outlet. Determine the force that will be exerted on the elbow. Assume the elbow is in the horizontal plane. pwater=1000kg/m3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

If you have a flat tire and need to pump up the tire on your car with a hand pump, what force do you have to apply to the pump handle? Assume the air pressure in your tire will be 20 lb/in2, that is 1.1 KPa (138,0000 N/m2). Let the air pump have a cross-section that is 5 cm in diameter. It depends on the weight of the car. About 270 N when the tire is full, not much when you start pumping on the empty tire. About 270 N for as long as it takes from the beginning. Just a few newtons until you are satisfied with how full the tire is because of the hand pump.
Air enters a fan through a duct velocity of 6.3 m/s and an inlet static pressure of 2.5cm of water less than the atmospheric pressure. The air leaves the fan through the duct at a velocity of 11.25 m/s and a discharge pressure of 7.62cm of water above the atmospheric pressure. If, the density of the air is 1.2kg/m3and the fan delivers 9.45m3/s, what is the fan efficiency when the power input to the fan is 13.75 kW at the coupling. Show schematic diagram and provide solutions.
Air flows steadily at low speed through a horizontal nozzle (by definition a device for accelerating a flow), discharging to atmosphere. The area at the nozzle inlet is 0.1 m2. At the nozzle exit, the area is 0.02 m2. Determine the gage pressure required at the nozzle inlet to produce an outlet speed of 50 m/s
Consider the impeller of a centrifugal pump. The liquid enters the impeller at 0.3 m/s with 30° angle from the radial direction. The angle of the blade at the outlet is ß₂ = 60°. The inlet and outlet radii are 20 cm and 30 cm. The speed of the impeller is 800 rpm. The liquid density and volumetric flow rate are 900 kg/m³ and 0.5 m³/min. Determine (a) the liquid velocity at the outlet of the impeller. (b) the hydraulic power with pump efficiency equal to 75%.
A certain 15-Kw pump running at 1600 rpm has an inlet diameter of 20cm and the discharge line is 12 cm in diameter. The output from th pump is 2800 liters/min of 20C and the centerline of the pump discharge is 1.5 meter above the centerline of the intake pipe. Determine the efficiency of pump. Please show complete solutions and formulas used. Show schematic diagram too.
Calculate the work in megajoules (1 MJ = 1x 106 J) required to pump all the water out of a full trough from which water exits by pouring over the sides. b a Assume that a = 4 m, b = 11 m, c = 13 m, and h = 2 m. The density of water is 1000 kg/m³, and g = 9.8 m/s". (Use decimal notation. Give your answer to two decimal places.)
Air enters a fan through a duct velocity of 6.3m/s and an inlet static pressure of 2.5cm of water less than the atmospheric pressure. The air leaves the fan through the duct at a velocity of 11.25 m/s and a discharge pressure of 7.62cm of water above the atmospheric pressure. If the density of the air is 1.2kg/cu.m and the fan delivers9.45cu.m/s, what is the fan efficiency when the power input to the fan is 13.75kW at the coupling?
A reciprocating compressor draws in 500 gal per minute of air whose density is 0.079 lbm/cu ft and discharges it with density of 0.304 lbm/cu ft. At the suction, p1 = 15 psia; at discharge, p2 = 80 psia. The increase in the specific internal energy is 33.8 Btu/lbm and the heat transferred from the air by cooling is 20 Btu/lbm. Determine the work on the air in Btu/min and in hp. STEP BY STEP EXPLANATION PLS
1. A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 40 k gm/s. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet. 50 cm Water 40 kg/s
Consider water flow through a horizontal, short garden hose at a rate of 30 kg/min. The velocity at the inlet is 1.3 m/s and that at the outlet is 11.75 m/s. The hose makes a 180° turn before the water is discharged. Disregard the weight of the hose and water. Taking the momentum-flux correction factor to be 1.08 at both the inlet and the outlet, the anchoring force (in N; hint: the answer is a negative number) required to hold the hose in place is ?
1. Water flows steadily with a velocity of 3.05 m/s in a 304.8 m long horizontal pipe having an inside diameter of 15.24 cm. The inlet and outlet pressures of the pipe are 689.3 kPa and 516.9 kPa,respectively. Find the friction in the pipe.
A reciprocating compressor draws in 500 cubic feet per minute of air whose density is 0.079 ft/cu. ft and discharges it with a density of 0.304 lb/cu. ft. At the suction, P, = 15 Psia; at discharge, P2 80 psia. The increase in the specific internal energy is 33.8 BTu/lb and the heat transferred from the air by cooling is 13Btu/lb. Determine the work on the air in BTU/min and in hp. Neglect kinetic energy.