Steam saturated at 68.9 kPa (10 psia) is condensing on a vertical tube 0.305 m (1.0 ft) long having an OD of 0.0254 m (1.0 in.) and a surface temperature of 86.11°C (187°F). Calculate the average heat-transfer coefficient using English and SI units. Determine also the heat transferred in the process.

Steam saturated at 68.9 kPa (10 psia) is condensing on a vertical tube 0.305 m (1.0 ft) long having an OD of 0.0254 m (1.0 in.) and a surface temperature of 86.11°C (187°F). Calculate the average heat-transfer coefficient using English and SI units. Determine also the heat transferred in the process.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A condenser consists of 5 pieces of 3 m long 1/4 in Sch 40 horizontal pipes lined up in 6 rows. It transfers cooling water with a heat transfer coefficient of 2000 W / m-K through the pipes. As the flow rate of the water is very high, the water temperature is constant at 35 degrees Celsius. Saturated heat vapor condenses at a pressure of 2 bars outside the pipes. Calculate the condenser capacity in kW
Which mode or condensation is characterized by larger heat transfer rates?
Saturated steam at 1 atm is condensed on the external surface of a copper tube withan outside diameter 16 mm and tube wall of thickness 0.5 mm. The tube is cooledinternally by water with a mass flow rate of 0.06 kg/s, which in turn is raised intemperature from 15 oC to 60 oC as it flows through the tube.Take the heat-transfer coefficient at the condensing side as 10.0 kW/m2K and theisobaric specific heat-capacity of water as 4180 J/kg K.i) Calculate the heat transfer rate to the cooling water. ii)
Industrial Pipes In very corrosive fluids, can the flow velocities in the pipes be high if the temperatures are low?
Industrial pipes For externally insulated pipes, is it necessary to use skids in the region of contact between them and the sleepers?
the question below is already answered in the photos that I provided I only want to ask how did it find the answersSaturated steam at a pressure of 25 psia is sprayed into a stream of moist air. The initial condition of the air is 55 dry-bulb temperature and 35 F de-point temperature. The mass rate of air flow is 2000 lb per min. Barometric pressure is 14.696 psia. Determine how much steam must be added in lb per min to produce a saturated air condition, b) the resulting temperature of the saturated air.my question here is:regarding of the solution pls elaborate how did it get w1 and h1 is it given in the psychrometric chart or it has a specific solution to follow
Q) Compare the heat transfer coefficients under the following conditions (Assume flow is turbulent). (1) Two fold increase in the diameter of the tube; the flow velocity is maintained constant by a change in the rate of liquid flow. (2) Two fold increase in the flow velocity by varying the mass flow rate. Comment on. the results.
The sensible heat-transfer coefficient for a dry surface has been determined to be 50 W/(m2-C) at a certain Reynolds number. Estimate the total heat transfer to the surface per unit area at a location where the wall temperature is 10 C and the state of the moist air flowing over the surface is given by 24 C dry bulb and 18 C wet bulb. Assume that the Reynolds number does not change and the Lewis number is 0.82. Assume that the condensate present on the surface will increase the transfer coefficients by about 15 percent
Determine the enthalpy of steam at 127 degrees celsius, at 80% quality, and flowing at the rate of 80kg/h, if it is used to heat fluid soup. What is the volume in m3 of steam required per hour of operation?
How would you formulate this problem to obtain a more meaningful result which desired to cool a gas has [Cp = 0.35 Btu/(Ib)(°F)] from 190 to 95°F, using cooling water at 83°F. Water costs $0.30/1100 f, and the annual fixed charges for the exchanger are $0.60/ft of inside surface, with a diameter of 0.0775 ft. The heat transfer coefficient is U = 8 Btu/(h)(f)(F) for a gas rate of 2900 Ib/hr. Plot the annual cost of cooling water and fixed charges for the exchanger as a function of the outlet water temperature. What is the minimum total cost?
Very urgent.
What is the equivalent evaporation of the boiler? Determine the specific heat capacity of the delivered steam