Steam power plant shown in figure is operating at steady state with water as the working fluid. The mass flow rate of the water circulating through the components is 50 kg/s. Determine: d) isentropic pump efficiency e) mass flow rate of the cooling water, in kg/s. f) rates of entropy production, each in kW/K, for the turbine and steam generator. Include all the relevant governing equations and references to the tables you use. Be organize

Q: SL-4 A reversible refrigerator is driven by a (non-reversible) heat engine with e-0.250. Both…

A: A reversible heat engine is a work producing device which is based on Carnot's cycle and its…

Q: As shown in the figure below, a reversible power cycle receives energy QH by heat transfer from a…

A: Given data:- Reversible power cycle (Carnot engine)

Q: 17-Initial pressure of 900 kPa and 80°C in a piston-cylinder assembly There is 734 grams of…

A: From steam table properties for R134a - The entropy at 900kPa and 80°C is 1.8552 kJ/kgKThe entropy…

Q: A certain coal-fired power plant has a rated power capacity of P = 950 MW. The output of this plant…

A:

Q: 5.4 In the continuous stirring heating tank, the flow rate of the influent is 200lb/min, the…

A: Write the expression of temperature variation. T=T0e-kt     80=90e-kt   ...... (1)

Q: in a steam power cycle, steam enters the turbine at 20 bar with the following different conditions…

A:

Q: 2. A boiler produces a steam at 2.417 Mpa and 468.9oC. The steam enters a turbine where after the…

A:

Q: An ammonia simple saturation cycle operates at 35 psia suction pressure and 172 psia condenser…

A: Given: The suction pressure, Ps = 35 psia = 241.316 kPa  The condenser pressure, Pd = 172 psia =…

Q: how to determine the Pressure and Volume at State 4 given the following data above. Note that State…

A: The molar specific heat at constant pressure,

Q: A power cycle produces 12 MW by partial conversion of the received heat as a result of steam…

A: Given Data Heat produce is :Q˙c=12 MW Saturated pressure is :Psat=1900 kPa Temperature of sink is:…

Q: 19. In the Brayton cycle shown in the figure, pressure drop at the heat sink is neg- ligible hence,…

A: Given:

Q: Water vapor at 20000kg /hour  flows into a steam boiler with a specific volume of 225 kPa 0.7565 m ^…

A: Write the given information.

Q: Q.1 Calculate Efficiency of the system, the net Work transfer & Heat rejected to sink for a Carnot…

A: Data given-  T1 = 285°C = 558 K  T2 = -11°C = 262 K  Q1 = 100 kJ

Q: 1 Different representation of gas cycle P 2Po D Ро V Vo 3Vo Figure 1: Problem 1, an ideal gas cycle.…

A:

Q: 1. In a turbine, steam enters with an enthalpy of 1275 Btu/lbm and leaves with an enthalpy of 1115…

A:

Q: In a heat engine, 3.00 mol of a monatomic ideal gas, initially at 4.00 atm of pressure, undergoes an…

A:

Q: As shown in the figure below, a reversible power cycle receives energy Qu by heat transfer from a…

A:

Q: A refrigerator is designed with a turbine instead of a throttle. What would you expect to happen to…

A:

Q: Q1:- In a R-134A based refrigeration system, a liquid-to-suction heat exchanger (LSHX) with an…

A:

Q: a 3-stroke cycle engine with processes of adiabatic expansion, isochoric heating, isobaric…

A:

Q: Qh=500kj

A: 5

Q: Air undergoes Isothermal expansion in a Carnot cycle where the pressure decreases from 2.5 MPa to…

A: Dear student z we are suppose to solve only 3 subparts. Still I have solved 5 sub parts. Please post…

Q: Steam at 100 bar, 625 C is received by a rankine engine and exhaust at 2 bar. (a) For an ideal…

A: Enthalpy calculations (Ideal)

Q: 24) Correct and rewrite the following sentences: 1. Time loss effects occur in the actual cycle…

A: 1. Time Loss Factor:  The time required for the combustion is such that under all circumstances some…

Q: Write the full energy balance equation for an open system with 1 inlet and 3 exit and operating in…

A: The steady flow energy equation is represented for the given condition for an open system.

Q: A reheat cycle with two stages of reheating is executed, with steam expanding initially from 2250…

A: Given: The turbine inlet pressure, P1 = 2250 Psi The turbine inlet temperature, T1 = 1060°F The…

Q: Q6. A steam power plant works on actual cycle with the following state points: State of point 2 is…

A: P2=Pmax=60 bar T2=400oc P3=Pmin=3 bar x3=0.95 x4=0 ηP=90%

Q: Steam of 6 MPa and 400-C produced in a boiler at a flow rate of 0.aa6 m³/sec is passed through a…

A: Given:  Boiler pressure, P1 = 6 MPa The Boiler temperature, T1 = 400oC The flow rate, Q = 0.046 m3/s…

Q: 2)Water vapor enters with a turbine, 2kg / s mass flow, 6 MPa pressure, 500 ° C temperature and 40 m…

A: As per company policy, we are restricted to solve only the first three sub-part of one question at a…

Q: Steam power plant shown in figure is operating at steady state with water as the working fluid. The…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: A reheat-regenerative Rankine cycle receives steam at 8.0 MPa, 300 °C and exhaust at 0.01 MPa. Steam…

A: Given data, Inlet condition of steam turbine is 8 MPa and 300 °C To determine:- 1) Percentage of…

Q: Q5. Choose the correct answer for each of the following: 1- The efficiency of the Otto cycle is…

A:

Q: A steam turbine is operating under the following conditions: steam to turbine at 900°F and 120 psia,…

A: GivenAt turbine entryT1=900oF=482.22oCP1=120psi=827.37KPaV1=250ft/s=76.2 m/sAt turbine…

Q: A 330 MW steam power plant operates according to the simple ideal Rankine cycle. water vapor enters…

A:

Q: Please answer all questions or leave for someone else to answer. A feedwater heater, operating in…

A: Given Inlet 1 Pressure = 5 MPa Temperature = 275o C Mass flow rate = 40 kg/s Inlet 2 Pressure = 5…

Q: Do the following: a.) Draw the P-V and T-S diagram, b.) Show the processes involved in the cycle,…

A:

Q: Octane is used as the working fluid in a gas-flow refrigeration cycle. The pressure ratio of the…

A:

Q: Specific Instruction: i.Drawaschematic diagramof each problem with labels of states of a…

A: To find: (a) The quality of the steam at the turbine exit. (b) The mass flow rate of the steam.…

Q: Exercise 2 Triangular Cycle. ble consider the reversible cycle below described by an Ideal gas. Xx…

A:

Q: A closed constant vohme system receives 10.5 kJ of paddle work. The system contains oxygen (k=1.395)…

A:

Q: An inventor claims to have developed a food freezer that at a steady state requires a power input of…

A: To determine:to investigate the inventor's claimgiven: powerpower input is heat transfer rate is the…

Q: Consider an ideal Brayton cycle of air where the pressure ratio ñ across the compressor is equal to…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.