Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the first turbine until it is just dry saturated, then it is re-heated to 400 °C and expanded through the second-stage turbine. The condenser pressure is 0.04 bar. High-P turbine Low-P turbine Reheater O Boiler -o P = P3 = Pecheat Condenser find thespecific heat inputof the systemin kJ/kg to 2.d.p. ?

Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the first turbine until it is just dry saturated, then it is re-heated to 400 °C and expanded through the second-stage turbine. The condenser pressure is 0.04 bar. High-P turbine Low-P turbine Reheater O Boiler -o P = P3 = Pecheat Condenser find thespecific heat inputof the systemin kJ/kg to 2.d.p. ?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A cooling system capacity Fifteen ton refrigeration, operating at 150 kPa in the evaporator, while in the condenser is 950 kPa. If refrigerant R-134a is in saturated conditions, calculate the power theoretical required to operate compressor. Power Compressor...kW.
ROOM (2) 700kPa х-0 CONDENSER (1) 40°C 700kPa EXPANSION VALVE (3) 100kPa EVAPORATOR (4) 100kPa x-1 OUTSIDE Consider a heat pump cycle operating with R134-a fluid at 0.01kg/s mass flow rate. Conditions are given in the figure. a) What are the values of heat supply rate to the room and heat absorption rate from the outside? b) What is COP of this heat pump? c) Assume we immediately put a watermelon of 8kg to the room at 2°C. Assuming a specific heat of 4200J/kg for the watermelon, how long will it take for the watermelon to reach room temperature of 20°C if we assume that heat pump only heats watermelon? COMP.
A steam condenser receives 10 kg per second of steam with an enthalpyof 2570 KJ/kg. Steam condenses into liquid and leaves with an enthalpy of160 KJ/kg, if cooling water passes through the condenser with temperatureincreases from 13 o C to 24 o C. Calculate the cooling water flow rate inkg/sec.
An ideal refrigeration system using R-134a, working at -10 °C and 40 °C for evaporator and condenser temperature respectively. What is the Pressure of condenser and Evaporator respectively in "bar" unit.
Reference Book: Introduction to Chemical Engineering Thermodynamics by Smith, Van Ness, etc. 7th or 8th Ed.
HOW will yOU you calculate the masS of steam circulated in a condenser?
When a steam boiler generates saturated steam at 2.5 mpa and the condenser pressure is 20 kpa, what is the Rankine cycle efficiency?Show complete step-by-step process and solution.
Q2: Two stage vapour compression refrigeration system with water intercooler uses R-22 as shown in figure 2 below. The evaporating temperature is -40 °C and condensing temperature 40 °C. The refrigeration capacity is 10 TR and the compression is adiabatic reversible process. The refrigerant leaves the water intercooler at 10 °C. Draw the cycle on p-h diagram and determine:- 1- The refrigerant mass flow rate. 2- Work done of each compressor. 3- Condenser heat load. >4- Coefficient of performance. 60 1
Steam is supplied to a two-stage turbine at 48 bar and 400 °C. It expands in the first turbine until it is just dry saturated, then it is re-heated to 400 °C and expanded through the second-stage turbine. The condenser pressure is 0.04 bar. High-P turbine Low-P turbine Reheater - Boiler P4= P3 = Preheat Condenser Determine thespecific work outputof the system to 3 d.p.?
High pressure steam З МРа 1 Power Out Turbine Medium/low pressure steam To process 100 КРа 200°C 500 КРа 2 Condenser 3 Figure Q3. Table Q3. Mass flowrate of steam Last ID. Number Mass flowrate of steam (kg/s) 0,1 5 2, 3 4, 5 7 6, 7 8. 8, 9 9.
What is the specific enthalpy in kj/kg for state 1
A refrigeration unit utilises ammonia as the refrigerant. The diagram for the circuit isshown in Figure Q3 below, with the following conditions: point (1) is a saturated liquidat –30 oC, points (3), (4) and (7) is a saturated liquid at 10 oC and point (5) is a saturatedvapour at –30 oC. The isentropic efficiency of the compressor and pump is 80% and itis assumed there are negligible heat losses to the surroundings. The liquid ammoniahas a specific volume of 0.0015 m3 kg-1. (a) Discuss which factors must be considered when selecting an appropriate refrigerant?(b) Calculate the coefficient of performance (COP) of the cycle.(c) If the effect of refrigeration is 10 kW, determine the required mass flow rate.