Steam flows through a nozzle at mass flow rate of m = 0.1 The enthalpies at inlet and exit are 2500 kJ/kg and 2350 kJ/kg, respectively. Assuming negligible velocity at inlet (C, = 0), the velocity (C,) of steam (in m/s) at the nozzle exit kg/s with a heat loss of 5 kW. (correct to two decimal places) a- 5 kW is h, = 2500 kJ/kg C,-0 h= 2350 kJkg C2 m-0.1 kg/s

Steam flows through a nozzle at mass flow rate of m = 0.1 The enthalpies at inlet and exit are 2500 kJ/kg and 2350 kJ/kg, respectively. Assuming negligible velocity at inlet (C, = 0), the velocity (C,) of steam (in m/s) at the nozzle exit kg/s with a heat loss of 5 kW. (correct to two decimal places) a- 5 kW is h, = 2500 kJ/kg C,-0 h= 2350 kJkg C2 m-0.1 kg/s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A quantity of a certain perfect gas is compressed from an initial state of 0.081 m, 1 bar to a final state of 0.034 m, 3.9 bar. The specific heat at constant volume is 0.722 k/kg K, and the specific heat at constant pressure is 1.03 kl/kg K. The observed temperature rise is 123 K. Calculate the mass of gas present to two decimal places with the Si unit.
Thermodynamics
Refrigerant 134a enters an insulated diffuser as a saturated vapor at 80°F with a velocity of 1400 ft/s. The inlet area is 1.4 in?. At the exit, the pressure is 400 lb;/in? and the velocity is negligible. The diffuser operates at steady state and potential energy effects can be neglected. Determine the mass flow rate, in Ib/s, and the exit temperature, in °F.
T10a please help me with the answer and full solution
Draw a figure and show the solution
Box the final answer. Write legibly. Steam flows into a turbine at a rate of 3.5 kg/s and ¾ MW of heat are lost from the turbine. Ignoring elevation and kinetic energy effects, calculate the power output from the turbine in KW? Steam pressure entering the turbine is 62 Bar at 440ºC and leaves at 74 Kpa.
8. During the drive, you can take fresh air using the conditioning system available in the automobile. However, you should slightly open (about 1 cm) your window for the exhausting some air, according to the mass balance principle. If you open your window completely, the intake of fresh air and exhaust of polluted air will deteriorate. Based on this information, what do you think about pressure balance? A) Pautomobile Poutside B) Pautomobile = Poutside C) Pautomobile > Poutside D) Pautomobile SPoutside 9. Which temperature measurement device is mostly used in industry? A) Gas thermometry B) Thermocouples C) Bimetallic thermometers D) Thermal Camera 10. Which measuring instrument should be preferred to convert qualitative measurement with thermochromic liquid crystals to quantitative data. A) Resistance Temperature Detector B) Thermocouples C) Bimetallic thermometers D) Thermal Camera 11. Which of the temperature measurement technique is used for visual warning of certain temperature…
Air expands adiabatically in a piston-cylinder assembly from an initial state where p₁ = 100 lbf/in.², v₁ = 3.704 ft³/lb, and T₁ = 1000 °R, to a final state where p₂ = 30 lbf/in.²2 The process is polytropic with n = 1.4. The change in specific internal energy, in Btu/lb, can be expressed in terms of temperature change as Au = (0.171)(T₂ - T₁). Determine the final temperature, in °R. Kinetic and potential energy effects can be neglected. T₂ = i °R
1. solve step by step and show proper conversion and cancellation of units.
An oxygen gas R = 0.2598 KJ/kg°k and k = 1.395. If 4 kg of oxygen undergo a reversible non flow constant pressure process from initial volume =1.2 cubic meter and initial pressure = 690 kPa to a state where final temperature = 600°C. 1. Determine the Change in Internal Energy. choices: a.200.60 KJ. b.198.45 KJ. c.99.54 KJ. d.200.55 KJ 2. Determine the constant pressure-specific heat. choices: a.0.9865 KJ/kg-°K. b.0.9175 KJ/kg-°K. c.0.8580 KJ/Kg-°K. d.0.7843 KJ/kg-°K need complete solution, cancellation and symbol:)
Helium expands polytropically through a gas turbine according to the process PV^1.419 = C. If the turbine produces 27.09 MW,. determine the heat transferred in kJ/s.
b) Steam generators are a type of heat exchanges that are used in power plants to generate steam at desired pressure and temperature (Fig. Q1.b). In a steam generator, saturated liquid water at 30°C enters a 60-mm diameter tube at the volume flow rate of 12 L/s. After exchanging heat with hot gas, the water changes to steam and leaves the generator at a pressure of 9 MPa and a temperature of 400°C. During this process, the diameter of the water/steam tube does not change. Steam out Gas out Hot gas in Liquid water in Fig 2. Schematic of the steam generator in Q1.b. (i) Calculate the steam mass flow rate (ii) What is the inlet velocity of the steam? (iii) What is the exit velocity of the steam? (iv) Calculate the rate of heat transfer (in MW) required to change the phase of liquid water to steam.