Steam enters a turbine at 3MPA and 471.245 °C at a rate of 8kg/s and exits at 0.2 MPa and 179.96°C. The steam is losing heat to the surrounding air at 20°C at a rate of 300KW. Neglect changes in the kinetic and potential energy of the stream. Determine, using the steam tables : (a) the state of steam at the inlet/exit of the turbine, as well as the actual power output of the turbine (b) the process efficiency of this turbine (c) the maximum possible useful work of this turbine in kJ/kg

Q: Pictured below is a multiplication problem worked out using the Egyptian method and Egyptian…

A: Consider the given diagram and see row 1 and row 2.

Q: A set of sprockets is constructed, as shown in Figure 1, so that the second and third rotate on a…

A: Solution: Given Data: r1=1 cmr2=4 cmrc=1 cmr3=3 cmN1=y rpmN2=u rpmN3=x rpm   To Find: (a) N1N2(b)…

Q: The beam AB is homogeneous and has a mass of 5,191. The tension in the cable of the crane can not…

A:

Q: How would you solve this manually without an equation solver

A:

Q: In Figure Q5, the 17 kg of circular disk is originally rotating with a clockwise angular velocity, w…

A:

Q: create 2 fourbar designs that include the dimensions and angle of motion

A: It is asked to draw four bar mechanism with given motion

Q: What is the period in seconds?

A: To determine: The time period for the swing, where it takes approximately 2 seconds to reach on side…

Q: Write the G-code with describe each lines : 20.0 40.0 40.0 40.0 60.0 30.0

A:

Q: For the system given in the figure on the right-hand side, where the input is four-unit step i.e., r…

A: givenAs per the Bartleby policy I am solving Part a, b, c and d.

Q: 4. Design 4-bit left and right rotators. Sketch a schematic of your design.

A:

Q: A container fill with an unknown liquid has three holes as shown in Figure Q1 (a). Determine the…

A:

Q: Help , Handwritten only. No Chatgpt

A:

Q: Cite all types of kinematic links?

A: kinematic link:kinematic link or element is defined as the part of a machine that has a relative…

Q: What's the answer for Q4 D and E with working out and answer as you already answered A-C

A: a) Write the expression for the specific speed. Here, N represents the rotational speed of the…

Q: Draw velocity polygon.

A: Solution:

Q: 4 HO PROBLEM: Based on the Orthographic Projections of the TERMINAL BLOCK draw a full section.

A:

Q: QI\ AFind the value of the complex number (1- i) ?

A:

Q: EX6:write a program read any vector and print the odd number only?

A: Note: Here you didn't mention any programming language so we are creating the program in the C++…

Q: In a slider crank mechanism (schematic shown the figure), the crank rotates at 60 revolutions p…

A:

Q: Consider the floating point system F and answer the following questions. Your solution to each part…

A: y=cos6xwe should use dx slice & the washer methodwasher have outer radius R=…

Q: Please show the computation in solving for NB and FAB

A:

Q: Draw the following spring with all mensions in sheet (write down all the equations you used in the

A:

Q: . Convert the decimal number 35710 into its binary number equivalent.

A: Given: A decimal number is, (357)10 .

Q: a Show how Pip can complete the circuit by adding less than 120 cm of track. b Show how Pip can…

A:

Q: write a G-code

A:

Q: SI) Standard Sizes of Woodruff Keys 1210?

A: The dimension of ANSI 1210 KEY IS GIVEN AS

Q: What is Line G?

A: Solution:

Q: Q4 Draw Front, Top and side view of the drawing shown below. All dimensions in mm and scale 1:1.

A: Required Front view, Top view and side view are drawn using first angle method of projections.

Q: Q4. Draw a neat sketch to represent the following readings on scales of Vernier Caliper: 132.85 mm…

A: Given1) vernier scale reading  =132.85mm2) vernier scale reading =8.68mm

Q: g, G codes, and M codes are cove

A: • CNC Program: A program utilized in PC Numerical Controlled Machine to perform activities is known…

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.