Soundness of cement is tested using 1. Turbidity meter 2. Le Chatelier's apparatus 3. Vicat's apparatus 4. Briquette

Q: 1. Determine the tension developed in cable AB when FA= 3 kN and FB = 4 kN. Submit your answer in…

A:

Q: Example 3 A 50-mm diameter bar is used as a simply supported beam 3 m long. Determine the largest…

A: Given:  Length of Beam = 3m Diameter of Beam =50mm Flexural stress = 50MPa   To Find: Largest…

Q: A golf club head is made from aluminum having a specific weight of 0.10 Ib/in3. In air it weighs…

A:

Q: (b) Fat, oil and grease from restaurants have been identified as a significant blockage in the…

A:

Q: A 50 dm diameter well gives a discharge of 0.05 m³/sec. Two observations well were made at a…

A: Given data,  q = 0.05 m³/s B = 10 m Diameter of well = 5 meter

Q: Jar testing was performed using alum on a raw drinking water source that contained initial turbidity…

A:

Q: Solve the following beam by superposition method, elaborating its diagrams of shear and complete…

A:

Q: The strength per meter of the longitudinal joint of a cylindrical tank is 475 kN, whereas the girth…

A:

Q: In the space above the mercury column in a barometer tube, the gauge pressure of the vapour is

A:

Q: fluid on the bottom of a tank. Compute the force exerted by the cylinder on the bottom of the tank…

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: (c) An analysis of a water sample has produced the following concentrations, as shown in Table 1(c).…

A:

Q: Q.1.1 A cable of uniform cross-sectional area is stretched between two supports 80 m apart with one…

A:

Q: A 50 mm2 steel bar in a machine structure is 1 m long. It has to resist a strain energy of 100 Nm…

A: Given data, Area of steel bar = A = 50mm² L= 1m = 1000mm Strain energy= u = 100Nm = 100×10³N-mm Fos…

Q: A cylindrical shaft of diameter 'D' is subjected to a uniformly distributed torque of T kN-m/m as…

A:

Q: Find the moment of force 2000 N about point 0 (in Nm). Consider clockwise moment as negative. B 5 m…

A:

Q: The beam shown is fixed at A and to be supported by rod BC at B. The beam carries a uniform load w =…

A: Given:- E = 200 GPa I = 450 x 106 mm4 Deflection formulaδ=wL48EIδ=PL33EIδ=Pa26EI3L-aa=Intermediate…

Q: In the figure, a 2" pipe leads downhill from a reservoir and discharges into air. If the loss of…

A:

Q: With a concentrated load of "P" at the middle of length "L". Compute the Reactions for Concentrated…

A:

Q: Which property is a better measure of the productivity of an aquifer: porosity or hydraulic…

A: Porosity and hydraulic conductivity are two important properties of an aquifer that determine its…

Q: A simply supported beam, 0.05 m in wide by 0.1 m in high and 4 m long is subjected to a concentrated…

A: to find max fibre stress

Q: Figure 16 shows the construction of the platform for the raft described in Problem 31. Compute its…

A: Volume =2×Lids+4×strutsLids=0.5in thick× 6ft width ×8 ft lengthstruts= (6in-2×0.5) thick×…

Q: 1. For the girder shown. Draw the influence line for the a) support reactions, b) moment at C, c)…

A: Influence lines are representing a graph that shows the variation of that function like a reaction,…

Q: If the cone shown in Figure 22 is made of pine wood with specific weight of 30 Il it be stable in…

A: Given:- d=6 inches h=12inches specific weight  in case 1 = 30 lb/ft3 specific weight  in case 2 = 55…

Q: The U-tube shown in Figure Q3 (a) is rotated about one of its arms at an angular speed of o rad/s.…

A:

Q: 2) Determine the reaction forces at both walls, if temperature is raised from 30°C to 90°C. The…

A: Given :- Temperature is increased from 30°C to 90°C