Solve this question Given a circuit with an applied voltage v- 340 sin teor - 60) volts and a resulting current i - 133 sin tar- amperes, determine the complete power triangle. 47)

Q: An alternating voltage is given by v1 = 75 sin( 200 Ttt -0.25 ) volts. What is the phase angle…

A: Phase angles Difference in degree= -45°

Q: D1 Vm A Ry 50HZ A. K

A:

Q: Determine the value that the ideal voltage source "E" must have in order for it to be the intensity…

A: The circuit is given asHere we need to calculate the value of E at which current flow through the…

Q: Determine the output waveform for the network of figure below and calculate the output dc level.

A: Given: Let Vs=supply voltageVo=output voltagef=60 HzVoltage drop across diode=0.7V( Si…

Q: Calculate the RMS current through R2 in the diagram IR1 = 6.06mA peak, R2 = 2.7 kohms, total…

A:

Q: 1.12. A certain load takes 10 kW at 0.5 pf lagging when connected to a 230-V, 60-Hz source. The…

A:

Q: Solve for VL1

A:

Q: A resistor and an inductor is connected in series across an AC supply. In this circuit, the current…

A: In circuit resistor R and inductor L is connected in series. So this circuit is RL circuit. So…

Q: An alternating voltage is given by v1 = 95 sin( 200 Tit -0.3 ) volts. What is the phase angle…

A: Given: V1=95 sin200 πt-0.3Volts V2=95 sin200πt

Q: Given the following Resistances and Inductors in Series and Voltage Source: R1 = 1,677 ohms R2 =…

A: Given the following resistances and inductors are in series with a voltage source, R1=1677 ΩR2=1966…

Q: A solenoid with an inductance of 0.25 H and a resistance of 100 is connected to a 120-V 60-Hz…

A:

Q: A wire carries a current i 3cos314t A. What is the average current over 6 seconds?

A: We are given, I = 3 cos 314t A. We need to find average value of current for 6 seconds.

Q: 30 ww 32 ww 30

A: Fig: Given circuit  In the given circuit upper and lower branch…

Q: There is a 110 Vac -60hz generator in series with a 48Vdc battery. For this series connection…

A: In this question, we need to determine the reading of coil voltmeter and iron voltmeter for the…

Q: An inductor and resistor are connected in parallel to a 120-V, 60-Hz line. The resistor has a…

A: An inductor and resistor are connected in parallel we need to find the phase angle between voltage…

Q: 6. Determine the rms current I as shown in figure 1. Source voltage is already in RMS value (Answer…

A: In this question,  We need to calculate the current I in the rms.  We are solving this problem using…

Q: If the voltage Vs = 800 mV, then the current %3D flowing in the primary winding Ip is: 1:8 -j202…

A:

Q: Solve for the value of the capacitance (in nF unit) if R2-1017 ohms and Xc = 2316 ohms. Round your…

A: The question is about finding capacitance value.

Q: Choose the correct statement for pure capacitor connected across single phase AC supply. O a. None…

A: Pure capacitor

Q: Based on Figures la,lb and 1c and RLC elements, write a discussion on voltage-current relations and…

A: In this question we will write about voltage current relationship and write about power factor...

Q: QUESTION 21 What is the inductance of an inductor that has 30 ohms of reactance at 60 Hz? Oa.,0658…

A: As per our guidlines ,we are supposed to do the first question only,if a student asks multiple…

Q: The current through a 15kohm resistor is given below, using Ohm’s Law to find the voltage, convert…

A: Ohms law V = IRGiven R = 15 kohmFor i1 = 3.5sin(2500t) mACurrent in polar form = 3.5<0° mAMath in…

Compensation Techniques

The compensation techniques are the methods that are employed in the electrical control systems to enhance the performance of the system. The performance are generally affected by the factors like lag in the compensating devices, slow response of the system of the components like sensors used in the control system. The basic compensation technique involves lag compensation, lead compensation or the combination of the both.