Solve for the force CD in the cable system shown The diagram is a structural engineering sketch depicting a beam supported at two points, A and D, with two downward forces applied at points B and C. Here's a detailed explanation:- **Supports**: - Point A and point D are fixed supports, represented with a symbol indicating fixed wall or structural support. - **Distances**: - The horizontal distance from point A to point B is 4 feet. - The horizontal distance from point B to point C is 7 feet. - The horizontal distance from point C to point D is 3 feet. - **Forces**: - A downward force of 800 pounds is applied at point B. - A downward force of 500 pounds is applied at point C. - **Height**: - The vertical distance from point D down to a reference horizontal level is 6 feet.This diagram likely represents a structural problem where the distribution of forces and the resulting moments on the beam need to be analyzed for stability and integrity, crucial for engineering calculations.

Weight at joint C is 500lbWeight at joint B is 800lb

Answered: Solve for the force CD in the cable…

Engineering

Civil Engineering

Solve for the force CD in the cable system shown

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: ind. Deterrmine the follow 1. Minimum tension in the parabolic cable

A: Hi! Thank you for the question As per the honour code, We’ll answer the first question since the…

Q: Cable ABCD supports the loading shown.Determine the tension in member BC,angle B1 and angle B2 6m…

Q: Problem 1 The bar supported by a pin at A and a cable at B carries a load of 260 N at C. Neglecting…

A: cable always carry tension so we make the free body diagram for analysis of the given beam. normal…

Q: A 600 N B 400 N C E D 150 mm 100 mm-150 mm- 80 mm 100 mm

A: Beam ABCD supported by cables BE and CF

Q: SITUATION. The suspended load exerts a force F-800lbs at A and bar OA weighs 300 lb. Assume that the…

Q: What is the x component of the reaction |(lb) (exerted on the boom by the wall) at C. A? What is the…

A: Given:- The Boom AC has a negligible weight The boom is supported by the cable D & E and…

Q: Member ABC, which is supported by a pin and bracket at C and a cable BD, was designed to support the…

Q: 3. Find the tension in the cable BC (15 pts) 12 ft 9ft 10,000 Ibs 12 ft 4. Find the reactions at…

A: Moment at hinge is zero

Q: E 1.732 m A 1.732 m D 3.0 m 3.0 m MA = 20kg %3D The tension in the cable supporting the box is…

Q: Q.11 A cable is suspended through simple support at the same level. The equivalent weight on the…

A: Given, Cable is suspended through simple support at the same level. Equivalent weight=10kN/m…

Q: *2-8 Part of a control linkage for an a rigid member CBD and a flexible cab applied to the end D of…

Q: Figure 2-83 7. Determine the maximum sag and the largest tension in 4k 24 1 4k the 30 ft 30 ft 30 ft…

Q: Determine the axial force, shear force, and moment at sections passing through a) C and b)…

Q: A cable is used as a laundry washing line whose end points are fixed at A and B. The clothes on the…

Q: Calculate the tension in the cable, and the reactions at A and C 100 mm 100 mm 300 mm 400 N C 400 N…

Q: Determine the tension in cable AB and the horizontal and vertical reaction components pin C exert on…

Q: determine the ff: The maximum tension in the cable The reaction at support B The reaction at…

Q: Determine the tension in each cable and the components of reaction at D

Q: 30° A B 800 16 30 in 30 in 30 in

A: Given Data: Angle between rope and beam = 30o Load acting on beam = 800 lb Let tension in rope be T…

Q: 1 2 45° A I35° 3 4 2 В W

Q: 2-111. Determine the angle 9 between the two cables. *2-112. Determine the magnitude of the…

A: Force in member AB, Force in member AC, To find: (1) Angle between two cables.…

Q: Solve for Ray and tension in the cable (TC)

Q: 6 KN 53 3m * 5m Find the tension on the cable Find the reaction at c Find the stress in the cable of…

Q: For the cable shown, determine the vertical reaction at B (N). 12 m 12 m | 12 m 12 m Inc hp=8m hE…

Q: wall crane supports

Q: The uniform rod in the figure shown weighs 500kN and has its center of gravity at G. Determine the…

A: The uniform rod is given as To find:- Tension in cable Reactions at A and B Concept:- A free body…

Q: the uniform concrete pole has a mass of 25 tons and is slowly being lifted to a vertical position…

A: Reference : Engineering Mechanics, Tension in cable. Given : Mass = 25 tons = 25000 kg A force P…

Q: A truss system carries a suspended 900kg crate at A. The cross sectional areas are 120 mm^2 and 150…

A: Given: A truss system Required: a. What is the axial force of the cable at B? b. What is the axial…

Q: A 30 kg mass M is held in place by the 50 N force F1, cable OA and cable Find the mass m of the…

A: Given : Mass M = 30 kg Force F1 = 50 N To Find : The mass m of counterweight to keep point O in…

Q: The homogeneous bar shown is supported by a smooth pin at C and a cable that runs from A to B around…

Q: For the beam and loading shown, determine the tension in the cable at D and the support reactions at…

Q: Question 2 Neglecting friction and the radius of the pulley, determine (a) the tension in cable ADB,…

Q: The 1635-lb uniform plate ABCD can rotate freely about the hinge AB. The plate is supported by the…

A: The weight of the plate will be concentrated at the centroid. Since the plate is symmetrical, the…

Q: 4 ft 8 ft y 7.5 ft 6 ft Question 8 x 6 ft What is the x-component of the reaction force at A (in lb)…

Q: The two loads are suspended from the ABCD cable as shown. dC = Since it is known to be 2 m, the…

A: ##Calculate the reaction at support D And It's Components At D of cable ABCD Since bending moment…

Q: The cable AB carries a uniformly varying load. It is connected to a wall at A and is held in…

Q: Member ABF is held in place by a ball-and-socket support at A and by wires GB, HD, and JF as shown.…

Q: For the cable shown .in, determine the following: 9. reactions for the cable b. the sag y at the…

A: To find cable length

Q: Problem 3 What are the value of Tension AC and AD if If the Tension of Cable AB is FN Newton to make…

A: Consider the Top view of the figure;

Q: Question 2 Cables extend from A to B and A to C. The cable AC exerts a 1500 lb force F at A. (a)…

A: (a) The position vector from point A to B is calculated as, rAB=0-0i+0-7j+10-0k=-7j+10k The position…

Concept explainers

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.

Question

Solve for the force CD in the cable system shown

The diagram is a structural engineering sketch depicting a beam supported at two points, A and D, with two downward forces applied at points B and C. Here's a detailed explanation:

- **Supports**:
- Point A and point D are fixed supports, represented with a symbol indicating fixed wall or structural support.

- **Distances**:
- The horizontal distance from point A to point B is 4 feet.
- The horizontal distance from point B to point C is 7 feet.
- The horizontal distance from point C to point D is 3 feet.

- **Forces**:
- A downward force of 800 pounds is applied at point B.
- A downward force of 500 pounds is applied at point C.

- **Height**:
- The vertical distance from point D down to a reference horizontal level is 6 feet.

This diagram likely represents a structural problem where the distribution of forces and the resulting moments on the beam need to be analyzed for stability and integrity, crucial for engineering calculations.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: To find force in cable CD

VIEW

Step 2: Solution

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please help me answer this. thank you. Book: Matrix Analysis of Structures By: Aslam Kassimali TOPIC: ANALYSIS OF BEAMS
Thank you so much <3
A beam of a T cross section is formed by nailing together two boards having the dimensions shown in the figure. 240 mm 60 mm |C 200 mm 60 mm If the total shear force V acting on the cross section is 1,600 N and each nail may carry 520 N in shear, what is the maximum allowable nail spacing s (in mm)? (Assume that the shear force acts parallel to the y-axis and is uniformly distributed across the thickness of the web.) mm
A beam is subjected to uniform force w as shown in the figure below, E of the entire section is 30000 kips/inch^2, I is 240 in^4, if point A is supported by 0.003 rad clockwise before assembly, and point B is supported at Subside 0.3 inches before assembly, try to calculate the reaction force of point A and point B.
Need help, please show all work, steps, units and round to 3 significant figures. Thank you!
Situation 3. Two plates are welded to form the section shown in the figure. The elastic section modulus, Sx of the section is closest to: a.1335 x 10^3 mm^3 b.3040 x 10^3 mm^3 c.5025 x 10^3 mm^3 d.7980 x 10^3 mm^3
A beam of a T cross section is formed by nailing together two boards having the dimensions shown in the figure. 240 mm 60 mm 200 mm 60 mm If the total shear force V acting on the cross section is 1,300 N and each nail may carry 400 N in shear, what is the maximum allowable nail spacing s (in mm)? (Assume that the shear force acts parallel to the y-axis and is uniformly distributed across the thickness of the web.) mm
■ Consider ■ h 457 × 152 × 52 UKB = 449.8 mm; b = 152.4 mm tw = 7.6 mm; t₁ = 10.9 mm r = 10.2 mm; d = 407.6 mm ■ h = 449.8 203.8 ■ What is the cross-sectional area, A? ■ What is the second moment of area, Iy? What is the elastic modulus, Wel,y? ■ What are the contributions of the flanges and the web? ■ What is the plastic modulus, Wply? ■ What are the contributions of the flanges and the web? ■ What is the shape factor of this section? b = 219.45 tw = 7.6 152.4 tf = 10.9 h₁ = 428
please answer, kindly see attached ref.
I need the answer as soon as possible
PLEASE SHOW COMPLETE SOLUTION and include figures and sketches
2:37 20.0 KB/S docs.google.com/forms 55 Write down your year and section. * Your answer Problem 1: The rigid bar AB is attached to two vertical rods as shown. If P=50KN, determine the vertical movement of points A and B. Your answer Figure for Problem 1 ALUMINUM L=4M A=50OMM? E=1OGPA STEEL L=3M A=30OMM? E=20OGPA A 2M 3M B -.