Solve all support reactions using the Method of Consistent Deformation. Consider B as the redundant.

Q: 3- Check the equilibrium of the material in the absence of body forces for the stress components in…

A:

Q: a) A holiow steel tube used in a roof structure has an outer diameter, d; = 104 mm and inner…

A:

Q: -termine the principal stresses, the maximum in plane d average normal stress. Specify the…

A: Since this a multiple question as per Bartleby policy, we can answer only first question, for other…

Q: The state of stress at a point is given by 0=x²y² + 30, 0₁y = x² + y² + 15. o = xy²2 + 30, T₁y =…

A: First we summarise the given data : To find : Determine the body force distribution at the point (…

Q: Analyre the trusses shown.EA constant 12 kN 10 KN 2 im 2 m 2 m

A:

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: The beam shown is subjected to two loads, one point and the other uniformly distributed. Determine…

A:

Q: Question-3 An element in pure shear is subjected to stresses -16 MPa, as shown in the figure. Using…

A: At the point when an structural member is stacked, deformation of the part happens and obstruction…

Q: determine the maximum load P that can be supported by the structure.

A: The values and diagram given in the question are as follows: The cross-section area of bar-1(A1)=125…

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: Q1. 1.) Determine the state of stresses at an orientation of 20 degree clockwise from the element…

A:

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: PROBLEM 10-n GIVEN: THE STATE OF STRAIN AT THE POINT ON THE PIN LEAF HAS COMPONENTS OF = 200(106), y…

A: εx=200×10-6 εy=180×10-6 γxy=-300×10-6 θ=-30o counter clock wise

Q: The triangular solid plate ABC is restrained by rod (1) at A and pin support at B. After applying…

A:

Q: Using finite element find :1.reaction and stress in all member | 文文 6m 6m 15.0 E-200 GPa D=0.05 m…

A: P=10kNThe diameter of the bar =0.05mE= 200 GP a.To find reaction forces and stresses in all members.

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: Pin-connected rigid bars AB, BC, and CD are initially held in the positions shown by taut wires (1)…

A: Strain is the result of a material's deformation due to stress. It's only a proportion of the length…

Q: The frame ABC is loaded as shown, determine the support reaction. 5kN/m 5kN/m 4m B 3m

A:

Q: Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of…

A: a = 40KN b = 22KN

Q: Determine the reaction at the roller at C of the beam shown below. Take EI= constant. Use the Method…

A:

Q: Determine the force in member CD of the truss shown in the figure. Circled values are areas in…

A:

Q: Determine the equivalent state of stress on an element at the same point oriented 0 = 40° clockwise…

A:

Q: The bars of the truss each have a cross-sectional area of 1.68 in2. Determine the average normal…

A:

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A:

Q: Q- If the principle stresses in a two-dimensional case are - 10MPa and 20MPa respectively, then find…

A: Given- Principal stresses- (-) 10 MPa & 20 MPa Maximum shear stress=?

Q: FOR THE ELEMENT SHOWN, DETERMINE THE MAXIMUM NORMAL STRESS AND SHOW IT ON A PROPERLY ORIENTED…

A: Given figure shows a stress element and it is required to find the principle stresses and maximum…

Q: Determine the moments at the supports of the fixed beam shown in Fig. 13.15(a) by the method of…

A: Given:- EI=constant fixed beam To find:- Moments at the supports

Q: Cylinder of height 2H. radius R. centroid at (0,0.H), axis e3 undergoes deformation x = o(z) = z +…

A:

Q: 1. В 21.

A:

Q: Links (1) and (2) support rigid bar ABCD shown in the figure. Link (1) is bronze [E = 15,200 ksi]…

A:

Q: The state of strain at the point on the leaf of the caster assembly has components of Ex=-400(10-6),…

A: Given data:-⇒εx=-400×10-6⇒εy=860×10-6⇒γxy=375×10-6⇒θ=30° NOTE= strain is dimensionless or unitless…

Q: Problem 3: The steel plate was originally in a rectangular shape. The 5 mm post-deformation geometry…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

A:

Q: Solve it

A:

Q: 1- 0.01 in. Undeformed - Deformed 0.10 in. 0.004 in. FIG. P2.39 0.12 in.

A:

Q: Use Method of Consistent of Consistent Deformation to solve the horizontal reaction at D in kN of…

A: Truss: Truss is a pin jointed structure which is subjected to vertical loading at the joint only and…

Matrix Algebra for Structural analysis

Structural analysis is a process in which the effects of different loads and internal forces, acting on structures and their elements are determined. This method of analysis is effective in detecting the failure loads of the structural elements and the design can be altered before commencing the construction process, which ensures proper strength and safety of the structures.