Skyline Manufacturing has decided to use an ABC costing system and has identified the following detailed information about its cost pools and cost drivers: Activity cost pools: • Materials handling: $55,000 • Machine maintenance: $20,500 Cost drivers: • • Number of material moves: 500 Number of machine hours: 50,000 Required: Calculate Skyline's activity rate for each cost pool.

Skyline Manufacturing has decided to use an ABC costing system and has identified the following detailed information about its cost pools and cost drivers: Activity cost pools: • Materials handling: $55,000 • Machine maintenance: $20,500 Cost drivers: • • Number of material moves: 500 Number of machine hours: 50,000 Required: Calculate Skyline's activity rate for each cost pool.

Cornerstones of Cost Management (Cornerstones Series)

4th Edition

ISBN:9781305970663

Author:Don R. Hansen, Maryanne M. Mowen

Publisher:Don R. Hansen, Maryanne M. Mowen

Chapter11: Strategic Cost Management

Section: Chapter Questions

Problem 24P: Evans, Inc., has a unit-based costing system. Evanss Miami plant produces 10 different electronic...

See similar textbooks

Similar questions

Evans, Inc., has a unit-based costing system. Evanss Miami plant produces 10 different electronic products. The demand for each product is about the same. Although they differ in complexity, each product uses about the same labor time and materials. The plant has used direct labor hours for years to assign overhead to products. To help design engineers understand the assumed cost relationships, the Cost Accounting Department developed the following cost equation. (The equation describes the relationship between total manufacturing costs and direct labor hours; the equation is supported by a coefficient of determination of 60 percent.) Y=5,000,000+30X,whereX=directlaborhours The variable rate of 30 is broken down as follows: Because of competitive pressures, product engineering was given the charge to redesign products to reduce the total cost of manufacturing. Using the above cost relationships, product engineering adopted the strategy of redesigning to reduce direct labor content. As each design was completed, an engineering change order was cut, triggering a series of events such as design approval, vendor selection, bill of materials update, redrawing of schematic, test runs, changes in setup procedures, development of new inspection procedures, and so on. After one year of design changes, the normal volume of direct labor was reduced from 250,000 hours to 200,000 hours, with the same number of products being produced. Although each product differs in its labor content, the redesign efforts reduced the labor content for all products. On average, the labor content per unit of product dropped from 1.25 hours per unit to one hour per unit. Fixed overhead, however, increased from 5,000,000 to 6,600,000 per year. Suppose that a consultant was hired to explain the increase in fixed overhead costs. The consultants study revealed that the 30 per hour rate captured the unit-level variable costs; however, the cost behavior of other activities was quite different. For example, setting up equipment is a step-fixed cost, where each step is 2,000 setup hours, costing 90,000. The study also revealed that the cost of receiving goods is a function of the number of different components. This activity has a variable cost of 2,000 per component type and a fixed cost that follows a step-cost pattern. The step is defined by 20 components with a cost of 50,000 per step. Assume also that the consultant indicated that the design adopted by the engineers increased the demand for setups from 20,000 setup hours to 40,000 setup hours and the number of different components from 100 to 250. The demand for other non-unit-level activities remained unchanged. The consultant also recommended that management take a look at a rejected design for its products. This rejected design increased direct labor content from 250,000 hours to 260,000 hours, decreased the demand for setups from 20,000 hours to 10,000 hours, and decreased the demand for purchasing from 100 component types to 75 component types, while the demand for all other activities remained unchanged. Required: 1. Using normal volume, compute the manufacturing cost per labor hour before the year of design changes. What is the cost per unit of an average product? 2. Using normal volume after the one year of design changes, compute the manufacturing cost per hour. What is the cost per unit of an average product? 3. Before considering the consultants study, what do you think is the most likely explanation for the failure of the design changes to reduce manufacturing costs? Now use the information from the consultants study to explain the increase in the average cost per unit of product. What changes would you suggest to improve Evanss efforts to reduce costs? 4. Explain why the consultant recommended a second look at a rejected design. Provide computational support. What does this tell you about the strategic importance of cost management?
Medical Tape makes two products: Generic and Label. It estimates it will produce 423,694 units of Generic and 652,200 of Label, and the overhead for each of its cost pools is as follows: It has also estimated the activities for each cost driver as follows: How much is the overhead allocated to each unit of Generic and Label?
The following product costs are available for Stellis Company on the production of erasers: direct materials, $22,000; direct labor, $35,000; manufacturing overhead, $17,500; selling expenses, $17,600; and administrative expenses; $13,400. What are the prime costs? What are the conversion costs? What is the total product cost? What is the total period cost? If 13,750 equivalent units are produced, what is the equivalent material cost per unit? If 17,500 equivalent units are produced, what is the equivalent conversion cost per unit?
Calculate bluefield activity rate for each cost pool ? General accounting
hello tutor please help me
please Give me answer fast and provide required
A company provides the following data from its activity- based costing system: • Designing products: Total cost = $420,000, Total activity 7,000 product design hours = • Setting up batches: Total cost = $60,000, Total activity 8,000 batch set-ups • Assembling products: Total cost = $30,000, Total activity 5,000 assembly hours What is the activity rate for the "designing products" activity cost pool?
General accounting
Gable Company uses three activity cost pools. Each pool has a cost driver. Information for Gable Company follows: Activity Cost Pools Total Cost of Pool Cost Driver Estimated Cost Driver Machining $ 250,000 Number of machine hours 84,900 Designing costs 56,000 Number of design hours 7,200 Setup costs 80,000 Number of batches 360 How do you find the activity rate?
what is the activity rate for this cost pool?
The pool rate is defined as the cost per unit of the cost driver for a particular activity cost pool. Group of answer choices True False Rocket Products manufactures three types of remote-control devices: Economy, Standard, and Deluxe. The company, which uses activity-based costing, has identified five activities (and related cost drivers). Each activity, its budgeted cost, and related cost driver is identified below. Activity Cost Cost Driver Material handling $ 225,000 Number of parts Material insertion 2,475,000 Number of parts Automated machinery 840,000 Machine hours Finishing 170,000 Direct labor hours Packaging 170,000 Orders shipped Total $ 3,880,000 The following information pertains to the three product lines for next year: Economy Standard Deluxe Units to be produced 10,000 5,000 2,000 Orders to be shipped 1,000 500 200 Number of parts per unit 10 15 25 Machine…
Need Answer with all working steps