Sketch shaper machine and explane its parts?

Q: Steam in a piston-cylinder assembly undergoes a polytropic process, with n=2, from an initial state…

A: Given data:- A polytropic process with a polytropic index n=2 and initial conditions volume…

Q: Expandable pattern is used in ?

A:

Q: What is the working principle of shaper machine?

A: Shaper machine is type of machine tool which is used for material removal process by relative motion…

Q: Subject: Machine Shop For pocket operation of 2 x 3-inch surface and depth of 0.06 in using 0.5 in…

A: The importance of cutting speeds and feed is very important and these factors will decide the…

Q: 10. A beam ABCDE with AB = 1 m, BC = 2 m, CD = 2 m and. DE = 1 m is supported by a hinge at B and…

A:

Q: Introduction for shaper work process please elaborate in 200 words

A: Shaper is a material removal machine of reciprocating type motion, and used for producing flat…

Q: spaced spacin formulation of this problem and (b) determine the nodal temperatures under steady…

A: Given: t=5 cm=0.05 m Nodal spacing 1 cm k=28 W/mCg=6 x 105 W/m^3 h=60 W/m2C TO determine Finite…

Q: Find Projections drawing?

A: Projection is the method used in mechanical drawing to draw a 3D object in the 2D plane for better…

Q: - Consider the four – bar mechanism in Fig. 1 with a velocity Va= 9.14 m/s, determine : A) all…

A: Angular velocity is the rotational velocity of a body. It is equal to the angular distance covered…

Q: milling machine operation in which the special profile

A: Milling machine can perform so many operations on a work piece. It can perform facing, turning,…

Q: A 1000 MW steam power plant, which is cooled by a river, has a thermal efficiency of 50 percent.…

A:

Q: Mention the difference between Shaper machine and planer machine?

A:

Q: A UNS G10350 steel shaft, heat-treated to a minimum yield strength of 75 kpsi, has a diameter of 1-…

A: Power is given by P =( T * n )/63025  T = F*D/2 Ssy = 0.577*Sy ( distortion energy theory)

Q: 1. A low-speed subsonic wind tunnel has a nozzle contraction ratio of 20. The pressure at the test…

A: Given data: v=80 m/sNozzle contraction ratio=1:20T1=300 KP1=Patm=1.01×105 Pa Need to determine the…

Q: Name the milling machine operation in which the milling cutter axis is perpendicular to the flat…

A: Answer is Face milling

Q: Describe about straddle milling operation

A: Explanation :-  Straddle milling - when two sides milling cutters are used to machine two opposite…

Q: With a neat sketch explain shaper machine

A:

Q: Draw the neat diagram of shaper machine and label all its parts.

A: Given:- Shaper machine To find:- To draw a neat sketch of the shaper machine and to label it

Q: What are the most essential parts of the Shaper Machine for it to function?

A:

Q: (8 10 6, 11 22 23 24 2 25 12 13 (6 (14.

A: given: name the part of lathe machine?

Q: How many parts per hour will a jig produce if the machining time is 30 seconds and it takes 2…

A: Given: Machining time=30 sec loading time=2 sec unloading time=2 sec

Q: Differentiate between Shaper and Planer Machine?

A: Shaper Machine                     Planer Machine Stroke length in the shaper…

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and…

A:

Q: briefly discuss the components of arbor press machine.  thanks

A:

Q: What is a tool bit ?

A: A tool bit is a non-rotary cutting tool used in shaper, lathe machine, and planner, such cutters are…

Q: Sketch and explain any four Shaper operations?

A: The four shaper operations are, Horizontal cutting: It's one of the most popular operations on a…

Q: Determine the support reactions and the forces in the member's CD, DH, and DH of the pin-jointed…

A: This question is based on the concept of trusses.

Q: Identify the name of the milling machine operation in which the concave contours can be produced.…

A: Form milling is the milling machine operation to produce irregular contours such as convex, concave,…

Q: save for Force in Rod AB: D. Equilibrium Equation (Sumof forces) 2). Geometry Equation Cie., what do…

A:

Q: How deep is the dovetail machined?

A: Solution:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.