SITUATION II: A propped 10 m cantilever beam is required to carry a load of 100 kN at midspan. If the yield stress of mild steel is 300 MPa, 6) Compute the plastic section modulus of the given beam. 7) Compute the elastic section modulus of the beam given that the shape factor is equal to 1.69. 8) Compute for the plastic moment of the given beam if an additional uniform load of 5kN/m is distributed along its total length.

SITUATION II: A propped 10 m cantilever beam is required to carry a load of 100 kN at midspan. If the yield stress of mild steel is 300 MPa, 6) Compute the plastic section modulus of the given beam. 7) Compute the elastic section modulus of the beam given that the shape factor is equal to 1.69. 8) Compute for the plastic moment of the given beam if an additional uniform load of 5kN/m is distributed along its total length.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

FE.Question 3.KK
A simply supported beam carries a concentrated load at the center which fluctuates from a value of W to 4 W. The span of the beam is 470 mm and its cross-section is circular with a diameter of 57 mm. Take ultimate stress of beam material as 683 MPa, Yield stress as 0.55 times ultimate stress and the endurance strength as 0.45 times the value of ultimate stress and take a factor of safety of 1.5. Calculate the maximum value of "W", if the variable stress induced in the beam is 109 N/mm?. Using Goodman relation calculate the value of mean stress in N/mm?. **Note: Please upload your handwritten working/solution to the link provided. Maximum Bending Moment Minimum Bending Moment Mean Bending Moment Variable Bending Moment Section Modulus, Z mm3 The value of Load "W". in N The value of Mean stress using Goodman relation ..
Q.3.L
Consider the following uniformly loaded simple beam. The beam has a span length L = 2.5 m, the load has a uniform intensity q = 3.8 kN/m, and the maximum bending stress o = 60 MPa. q = 3.8 kN/m L = 2.5 m The cross section of the beam is square, and the material is aluminum having modulus of elasticity E = 70 GPa. (Use the formulas of this example. Use available deflection formulas. All beams have constant flexural rigidity EI.) Calculate the maximum deflection 8, max: (Enter the magnitude in mm.) mm
Please help me solve this problem. Need it asap. Thank you.
A wood beam is strengthened using two steel plates as shown in the figure below. V 6 mm 150 mm 6 mm |B 100 mm i The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 13 KN q= 5.0 kN/m с 3 m Calculate the maximum tensile and compressive stresses of the beam. Assume that E = 11 GPa and E = 200 GPa. (Enter your answers in MPa. Use the deformation sign convention.) maximum tensile stress in wood MPa maximum tensile stress in steel MPa MPa maximum compressive stress in wood maximum compressive stress in steel MPa Need Help? Read It B 000 +1m-
STRESSES 1. A 150mm x 50mm board is glued to a triangular board. Determine the maximum shear stress of the adhesive IN BEAM material used to connect the boards. 20 KN 1 m 30 KN/m 150 mm 50 mm 1 m 1 m 15 KN/m 250 mm 15 KN/m 2 m 350 mm
A cantilever beam with cross section shown below and span of 3 m is subjected to concentrated load (P) at the free end. If the maximum allowable tensile stress equals to 10 MPa what is the maximum value of the load P can be applied.
Higdon
Problem 2 A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa), located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. 2m B 10kN/mm 4m C 2m Steel Aluminum 42 mm 20 mm 13 mun
A cantilever beam of length 6 m has an additional support at a distance of 2 m from its free end as shown in Figure 4. It has the cross-sectional dimensions with height h=300 mm, inside height h₁ =250 mm, width b= 150 mm, and inside width b₁=100 mm. It is made of an elastic perfectly plastic material having tensile and compressive yield stress of oy = 250 MPa. Determine the yield moment My of the beam Determine the plastic moment Mp of the beam ✓ By using force method and selecting the vertical reaction at C to be redundant, draw shear and bending diagrams using the graphical method. -Determine the minimum value of W at which collapse occurs B/2W C 77 2m 2m 2m C b₁