Situation 5: A W4x13 has a length of 3.5 m. Fy 248 MPa. The properties are given below. Properties of W shape A 2,470 mm^2 d-106 mm bf - 103 mm tf-8.76 mm kdes 15.1 mm tw- 7.11 mm rx-43.7 mm ry-25.4 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? 226 KN 215 KN. O 244 KN O 260 KN

Situation 5: A W4x13 has a length of 3.5 m. Fy 248 MPa. The properties are given below. Properties of W shape A 2,470 mm^2 d-106 mm bf - 103 mm tf-8.76 mm kdes 15.1 mm tw- 7.11 mm rx-43.7 mm ry-25.4 mm 1. Which of the following most nearly gives the axial capacity (Pa) of the column if one end is fixed and the other is pinned connected? 226 KN 215 KN. O 244 KN O 260 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A horizontal beam ABC is loaded as shown in figure below. The distance of the point of contraflexure from end A (in m) is 10KN beol C s no 2tos A 0.75m B o msed 6 1 m
Determine the (a) product moment of inertia at steel cross-sectional area with respect to centroidal axes and then (b) calculate the minor and major principal values of moment of inertia with respect to centroidal axes. (Imin Imax). 250 mm mm TUUR OS 350 mm 50 mm 150 mm
A high performance racing plane is to have an aileron control rod made out of unidirectional carbon fibre tubing with the following material properties: elastic modulus E = 90 GPa and compressive failure stress OF,comp= 600 MPa. In order to avoid parts of the internal wing structure the control rod is required to have a bend at the tip as shown in the figure. The rod is L = 400 mm long with an inner diameter of 8 mm and an outer diameter of 10 mm. The length of the bent portion of the rod is = 40 mm . The servo applies a maximum compressive or tensile force of F= 200 N on one end of the control rod as shown in the diagram. The end at which the loading is applied can be considered to be free and the other end of the control rod can be considered to be fixed. Consider the case where the servo applies a compressive force on the tip of the control rod: (i) (ii) X Find the maximum compressive stress in the rod and the maximum transverse deflection of the rod at B. Find the maximum…
P4: Calculate the design moment strength of the T-section shown in the following figure (fe' = 28 MPa and Fy = 420 MPa). 111 100 cm 3.5mm 3=22 350 E 3.25 m 250 3=22 3.25 250 m
I need the answer as soon as possible
SCS SHS 2122 Tn PSCS SHS 2122: Lo... Determine the axial force (kN) in each member of the assembly shown below, Member Cross-Sectional Area Modulus of Elasticity AB 1,000 mm2 200 GPa BC 1,500 mm2 200 GPa DB 1,000 mm2 200 GPa C 18KN A 400mm 400mm 00 50 55.00
BRIDGE DESIGN PROBLEM: USE AISC OR NSCP 2015 FOR SOLVING THE GIVEN PROBLEM.
Pls help me
E pe Vi5 For the frame shown below, the initial displacement is 25 mm and the initial velocity is 13 mm/s. Damping is 10% of critical. Cross-sectional dimension of each column is 250 mm x 300 mm and elastic modulus is 22.8 GPa. Determine (a) () (c) the natural frequency (rad/s) the amplitude the expression for the displacement 500 kN 3 m 5m 5 m
A block with a mass of 150-kg is supported by a cable which posses over a 150 mm diameter puley that is attached to a tame as shown in the figure. Determine al forces octing on member BCD ot the trame. 400 mm- 200- mm LOV 70 450 mm
Ex4:For the beam shown in the fig. blew find the valne of 0) ,using the data f'.= 40Mpa, fy = 414Mpa , L.L- 24, D.L - (self weight) 57.5mm LI-24ENm d=500mm Solurion:
Maximum shear force value A 2 ft B 100 lb/ft 2 ft 300 lb AC 200 lb 2 ft