SITUATION 4. Knowing that dc = 3m, determine the following: a. Distance d k2mk 2m 3m 3m b. Reaction at E c. Total length of cable. ds 4m B E 5kN 5kN 10KN

Q: Members BE, CE, and CF

A:

Q: State the depth of improvement ?

A: Soil engineering improves techniques to enhance the soil or ground. Vibro- compaction could be a…

Q: Explain the term Cunningham correction factor.

A: Cunningham Correction Factor (C): In dynamics of fluid, the Cunningham slip correction factor is…

Q: How to determine Z-value? How to determine D-value and TDT?

A: The Z-value is referred to calculation of the resistance of micro-organism at different temperatures…

Q: PROBLEMH2 ww 9. ww a. WwW SDLVE FOR Rab

A: Given:-

Q: Define the Strip loadings ?

A: Strip loads are a common type of foundation load. These types of loads are found on the strip and…

Q: What do you mean by the Bulk Richardson Number (BRN)?

A: The Bulk Richardson Number is defined as the ratio of turbulence due to kinetic energy to the shear.

Q: What are short stacks?

A: The short stacks are the reciprocating engine exhaust system.

Q: Define ULS requirement

A: The Ultimate Limit State is abbreviated as ULS.

Q: Engineers may accept outside work without notifying their primary employer. True False

A: Brief concept- There are certain ethical codes of conduct according to which the work should be…

Q: What is a secant Modulus?

A: Secant modulus:

Q: (b)       Define Bench Mark. List down its different types

A: A benchmark is a reference point that helps one to calculate something. A "bench mark" associated…

Q: What is susbtainable design?

A: Answer Introduction Sustainable design is defined as these are those that seek to minimize the…

Q: Define Stripping?

A: Brief concept- It is related to the construction part and also known as De-shuttering.

Q: Different types of roofs

A: Roof is the topmost component of the building that provide structural covering to protect the…

Q: Draw the complete shearing force diagram and bending moment diagram for the beam shown below. State…

A: A beam is simply supported at two ends. Two UDLs of 500 N/m at each end 0.3 m from the supports A…

Q: Describe about the Sliding Block Analysis.

A: The sliding block analysis method used by the Newmark is an engineering which determines permanent…

Q: of nsions? O Option 1

A: Option 1,2, 3 does not completely give the dimensions of their respective figures.

Q: Define Lateral Capacity

A: Lateral capacity:

Q: Qsn. Discuss the materials required to construct the building using PET bottles as an construction…

A: Materials Required The construction requires some of the basic materials which ensures  a stable,…

Q: Dewfine the term final completion?

A: During the closing process of the project, the final completion-also recognized as final approval is…

Q: What is shear starin rate?

A: Shear rate:

Q: 10 divisions of vernier scale are equal to 11 divisions of a main scale of each 0.1 mm. What is the…

A: Given data- 10 divisions of vernier scale=11 divisions of main scalemain scale one division=0.1 mmTo…

Q: What is Prebid?

A: A prebid is a meeting which generally happens before a bid. It is held to clear up any confusion…

Q: Slab on grade Define.

A: A slab-on-grade is a type of shallow foundation in which a concrete slab rests directly on the…

Q: What is over-consolidated?

A: There are 3 types of consolidation stages namely : 1- over consolidation stage 2- normal…

Q: Define the By Bowle's method ?

A: Joseph bowle presented a method/Formula to Determine Modulus of Subgrade Reaction .The Mehod is…

Q: Design Serviceability Limits

A: Design Serviceability Limits:

Q: (c) Determine the length of X and Y for the rectangular plate as shown in FIGURE Q1(b) if the area…

A: Area of rectangular plate, A = 2 m2.Perimeter of rectangular plate, P=2X+2Y = 500 cmIt is asked to…

Q: EARTHWORK SPECIFICATIONS oCut and Fill to Formation Level oGeneral oFill materials oFinish to…

A: Formation is a flattened surface of ground on which the pavement is settled. A non-structural…

Q: What is Bowles solution ?

A: Bowles Solution : The Bowels solution allows incorporating the influence of the cohesion on the root…

Q: "-Q3.33-. A cantilever beam as shown in the figure has a clear covering of 50 mm at the top and at…

A:

Q: Discuss  in  details coagulation

A: Coagulation is defined as the process of converting smaller dissolved solids into larger particles…

Q: a) b) User Coordinate System B d) User Coordinate Set. (a) r none of the boves, Bos birak

A: UCS stands for User Coordinate System. The correct option for the above-given question is an option…

Q: Define the Hiley's formula ?

A: Hiley's formula to calculate the ultimate capacity of the pile is given by, Qup=ηHηbWHS+C2 Here, ηH…

Q: What is ASD method

A: Allowable Stress Design (ASD) It is also known as the service load design or working stress design…

Q: What is a Subtense bar?

A: Subtense bar:

Q: Define the term Well Points.

A: A wellpoint is a well of small diameter used for dewatering.

Q: Define the  Modular ratio ?

A: Modulus of elasticity: The ratio of stress and strain is known as The modulus of elasticity. This is…

Q: Define Rooof Insulating..

A: Solution; Roof Insulating Insulation helps us to keep the desired temperature in the building. It…

Q: Q4: Convert the following into required: 1- An area 4.2 cm on amap with scale 1/5000 > Don , Olk,…

A:

Q: GEOFOAM Methodology - How is this material installed and/or maneuvered around site?

A:

Q: ee sentences only. 1. Grad

A: 1. The most basic type of resistance is grade resistance.The gravitational force that prevents a…

Q: Non-Homogeneous LDECC Solve the following and box your final answer. Please answer it in detailed…

A:

Sustainable use of materials

Sustainable use of materials is the use of resources (energy, natural resources), their impact on the environment and the specific risks to human safety. In construction, environmental friendly materials are those where, by their production, placement and storage, low environmental impact acts have been performed.