SITUATION 3:A solid shaft in a rolling mill transmits20 kW at 2rev/s. The length of shaft is3 m long and modulus of rigidity G =83 GPa9. Which of the following gives thetorque carried by the shaft?a. 1.59 kN.m b. 2.69 kN.mc. 3.45 kN.md. 4.81 kN.m10. Which of the following gives theminimum diameter so that theallowable torsional shearing of 40MPAwill not be exceeded?a. 88 mmC. 45 mmb. 59 mmd. 76 mm

Answered: Image /qna-images/answer/71f1cd5a-69ea-484c-9afb-d04495ac9a8c.jpg

SITUATION 3: A solid shaft in a rolling mill transmits 20 kW at 2rev/s. The length of shaft is 3 m long and modulus of rigidity G 83 GPa 9. Which of the following gives the torque carried by the shaft? a. 1.59 kN.m c. 3.45 kN.m b. 2.69 kN.m d. 4.81 kN.m 10. Which of the following gives the minimum diameter so that the allowable torsional shearing of 40MPA will not be exceeded? a. 88 mm C. 45 mm b. 59 mm d. 76 mm

SITUATION 3: A solid shaft in a rolling mill transmits 20 kW at 2rev/s. The length of shaft is 3 m long and modulus of rigidity G 83 GPa 9. Which of the following gives the torque carried by the shaft? a. 1.59 kN.m c. 3.45 kN.m b. 2.69 kN.m d. 4.81 kN.m 10. Which of the following gives the minimum diameter so that the allowable torsional shearing of 40MPA will not be exceeded? a. 88 mm C. 45 mm b. 59 mm d. 76 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
A beam ABC with a cantilever from B to C supports a uniform load of 3 kN/m over its entire length (see figure). The beam is a gutter with the dimensions shown in the figure. The moment of inertia about the z axis (the neutral axis) is equal to 210 cm⁴ . Calculate the maximum stress in tension σt and the maximum stress in compression σc due to uniform loading.
Problem 2: A solid circular shaft is acted upon by the torques as shown. If G= 12, 000 ksi determine: a. Rotation of wheel D with respect to A. b. Shear stress at point E Diameter of shaft: A-B = 2in C-D = 2in B-C = 4in Ti= 6 T in.kips T2=2 m in.kips T3= 5 m in.kips T4= 9 m in.kips T1 T2
Problem I. A homogencous, graded shaft with circular cross section is clamped at both ends and loaded by the torque Mo = 100 kN m Use a = 2 m, b = 3 m, ri = 25 mm, r2 = 40 mm, and G = 77.2 GPa. a) Compute the torques at the support positions A and B. b) Compute the angle of twist at the point where Mo is applied. 1 2r1 2r2 A Мо В a b
A machine having a mass of 4200 kg is supported by three solid steel rods arranged as shown in Figure P1-45. Each rod has a diameter of 20 mm. Compute the stress in each rod. A Rods. 55°. -35° D Machine
(+) The hollow shaft used in the system has the following conditions: В E Outer Ø: 110 mm Ø Allowable Shearing Stress: 85 MPa 18 KN•M Determine the thickness (mm) of the shaft. Round to the F 35 kN-m nearest whole number for the thickness and use 2 decimal places for other solved values. Provide 88 kN m a torque diagram, strictly follow instructed sign convention, and start from left to right. 35 kN-m
Determine the largest force P (to the nearest integer) which can be applied to the cord without causing motion. Blocks A and B have a mass of 15.5 kg and 18.5 kg, respectively. Use a = 1.15 m, b = 1.25 m, µ (AB)= 0.35, µ (A) = 0.15, g = 9.81 m/s?. D В b HAB P HA P (to the nearest integer) = N
7. Given: A centerline of 250 LF; Anchor Blots @ 48" OC; 2-doors; 8 corners. Calculate the number of anchor blots needed.
The continuous beam is loaded as shown below. a. b. C. determine the moment at point 1 (M₁) determine the moment at point 2 (M₂) determine the moment at point 3 (M3) T Ri 2M 70kn/m R2 фоко/м 2M ·Im R3
PA 5⁰1 MA Pully A of the treadmill is driven by a motor that can supply a moment M_A = 200 in.lb. Pully B is frictionless, and its bearing slides in a frictionless slot where force P tensions the belt. Both Pulleys A and B have 1.5 in, radius and the coefficient of static friction between pulley A and the belt is 0.3. Determine the smallest value of P needed to prevent slip between pulley A and the belt.
Example 1 The diameter of a shaft is 20 cm. Find the safe maximum torque which can be transmitted by the shaft, if the permissible shear stress in the shaft material is 4000 N/cm² and permissible angle of twist is 0.2° per meter length. Take G as 8x10 N/cm². If the shaft rotates at 320 rpm what maximum power can be transmitted by the shaft.
2. The maximum tension that can be developed in the cord shown in Fig. below is 500 N. If the pulley at A is free to rotate and the coefficient of static friction at the fixed drums B and C is µs = 0.25, determine the largest mass of the cylinder that can be lifted by the cord. D B 45