Situation 2. A continuous beam is shown in the figure no. 2 with a constant value of El. 4. Which of the following most nearly gives the value of slope at B (in kN.m²)? 41.25/EI c. 48.56/El 35.79/El d. 28.97/EI 5. Which of the following most nearly gives the value of the moment at support A (in kN.m)? a. b. a. -54.30 c. -34.60 b. -87.30 d. -92.80 6. Which of the following most nearly gives the value of the moment at support B (in kN.m)? a. -114.30 b. -120.50 c. -124.60 d. -105.30

Situation 2. A continuous beam is shown in the figure no. 2 with a constant value of El. 4. Which of the following most nearly gives the value of slope at B (in kN.m²)? 41.25/EI c. 48.56/El 35.79/El d. 28.97/EI 5. Which of the following most nearly gives the value of the moment at support A (in kN.m)? a. b. a. -54.30 c. -34.60 b. -87.30 d. -92.80 6. Which of the following most nearly gives the value of the moment at support B (in kN.m)? a. -114.30 b. -120.50 c. -124.60 d. -105.30

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 20 - In the cantilever beam in the figure, bar clearance L= 225 cm and single load acting on the…

Q: II. Method of Superposition Problem 4. Draw the moment diagram for the beam using method of…

A: Bending moment at a section can be found be superimposing(adding) the bending moments due to the two…

Q: 30 kN 10 kN/m -2 m В 5m -3 m A

Q: Determine the required magnitude of the couple moments M2 and M3 so that the resultant couple moment…

A: First, we draw the free body diagram of the problem:-

Q: A frame with fixed support at A and a roller support at D, Assume EI is constant. Using…

Q: Draw the shear and moment diagram 5KN/m. A 10m

Q: Analyze the statically Indeterminate Beam shown and Draw the shear and Moment Diagram. P =30 kN L =…

A: Bending moment at 4m = -45 + 30 x 4 - 30 x 2 = 15 kN.m

Q: 1. Compute the reactions and draw the shear and moment curves for the beam in the Figure. Assume…

A: Given: Required : Support reactions, shear force diagram and bending moment diagram

Q: Superposition Problem 4. Draw the moment diagram for the beam using method of superposition.

A: Drawing of moment diagram for beam using method of super position

Q: 1.50 25kN ! Using moment distribution method. Calculate the moment at A and B 6.50 6.50 25kN 1.50 B

Q: PROBLEM #1: Analyze the cantilever shown. Calculate the reactions at support. Solve the deflection…

Q: The simply supported beam in the figure is loaded by the clockwise moment 10 kN-m at B. Draw the…

Q: Determine the slope of the beam shown in Figure (a) at polnt B If P-100 kN, L 2 m, E 200 GPa and I-…

A: Given data : Point load (P)=100 KNLength (L)=2 mE=200 GPaMomemt of inertia (I)=35×10-6 m4

Q: 2. Assuming the upward reaction of the ground on beam AB to be uniformly distributed, (a) draw the…

A: Beam: Objective: (a) Draw the shear and bending moment diagram. (b) Determine the maximum absolute…

Q: 4. Determine the member end moments and reactions for the three- span continuous beam shown due to…

A: Three span Continuous beam with uniformly loaded of intensity 32 kN/m Support settlement at B = 15…

Q: Draw the free-body diagram of the ring B.(Draw the vectors starting at the black dot) 2. Determine…

A: The free body diagram for point B:

Q: F1 O1 A D -2 m -3 m 1 m

Q: 11. Method of Superposition Problem 4. Draw the moment diagram for the beam using method of…

Q: Solve for the following for the built-up I-section shown. Horizontary and (d) Identify which axis is…

A: Given:Required:Identify the stronger and weaker axisSection moduli about stronger and weaker…

Q: 2000 N 3 m - 2 m - 2 m– 60°

Q: Draw the M,N,V diagrams of the overhanging beam given in the figure and determine the maximum…

Q: 2.) For the given beam ABCD, determine the following: a. The Shear and Moment Diagram of the beam…

Q: Calculate vertical reaction at A , D in kN. Calculate the maximum Postive shear in kN. Calculate the…

Q: A propped beam shown below is loaded with UDL along its entire span. Determine the following: (Mc)…

Q: 48 kN/m 19.96 KN A 41 21 C D -4 m- -3 m 1.5 m

A: Moment distribution method - when kinetic determinacy of structure is less than static indeterminacy…

Q: Solve the problem using Moment -Area Method Problem III. Determine the support reactions at B and…

Q: Problem no. 1 Determine the slope and the displacement at the end C of the beam. . 8 kN 4 kN A D B-…

Q: SOLVE FOR THE REACTIONS AND DRAW THE SHEAR AND MOMENT DIAGRAMS OF THE FOLLOWING BEAMS PROVIDE A…

Q: The resultant of the three forces shown is a counterclockwise couple of magnitude 150 kip-ft.…

A: To find out the magnitude of all forces.

Q: Find the distance X1, if the moment at midspan is zero. a. 2.5 m b. 3.0 m c. 2.25 m d. 2.75 m

A: Overhanging portion length given X1 Hence Length between the support 10-2X1 So Length from midspan…

Q: From the beam shown with fixed end support at A and rollers at B... From the beam shown with fixed…

Q: Draw the M,N,V diagrams of the overhanging beam given in the figure and determine the maximum…

Q: Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I = 70(106) mm². Use…

Q: Draw the M,N,V diagrams of the overhanging beam given in the figure and determine the maximum…

Q: Q4. ANALYZE THE GIVEN STRUCTURE USING THE MOMENT DISTRIBUTION METHOD NOTE: STOP AT THE 5TH ITERATION…

Q: Draw the M,N,V diagrams of the overhanging beam given in the figure and determine the maximum…

Q: 80 kN 30 kN/m B D A -10 m + 5 m 5 m– El = constant

A: Distribution factor: It is defined as the ratio of the stiffness of a member to the total stiffness…

Q: SITUATION. Refer to the figure. A bin holds a cylinder as shown. Each cylinder weighs 800 kN and has…

A: Question number 2 and 3 are different questions and is not a part of the three cylinders question.…

Q: SITUATION. The beam shown is subjected to a uniform dead load of 1.2 kN/m, a concentrated dead load…

A: w = 1.2 KN/m PD = 45KN PL = 40KN

Q: Find the M, R. and R.using the Three Moment Equation. 10KN/m 5 kN/m B 6

Q: Determine the internal moments in the beam at the supports (MAB, MBA and MBC), using the slope-…

Q: For the solve for continous beaun shown, draw the ✓ and u diagram of Ely at the overhang. the value

A: To determine:Shear force and bending moment diagram

Concept explainers

System of Forces

A force is an external influence or agent that changes the state of a system. According to Newton's second law, the force applied to a body is proportional to the change in momentum of a body. Hence, whenever a force is applied to a body, its momentum changes. If the body is at rest, under the action of force, its state of rest changes to motion. In other words, the magnitude of the momentum of the body changes from zero to a measurable value. Similarly, if the body possesses some initial velocity, it has some associated momentum, the effect of force can cause the body to halt or come to rest, that is, the momentum reduces to zero.

Question

a. I
b.
C.
d.
Situation 2. A continuous beam is shown in the figure no. 2
with a constant value of El.
4. Which of the following most nearly gives the value of
slope at B (in kN.m²)?
41.25/EI
35.79/El
5. Which of the following most nearly gives the value of the
moment at support A (in kN.m)?
a.
b.
a.
b.
c. 48.56/El
d. 28.97/El
-54.30
-87.30
6. Which of the following most nearly gives the value of the
moment at support B (in kN.m)?
a.
-114.30
b. -120.50
c. -34.60
d. -92.80
c. -124.60
d. -105.30

5 m
80 kN
5 m
B
Figure no. 2
20 kN/m
10 m
5m
D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 8 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

ANSWER SHOULD BE ANSWER KEY: 60) 96.8 61) 54.42 62) 48.38
A propped beam shown below is loaded with UDL along its entire span. Determine the following: (Mc) C. a. Determine the reaction (R) b.Determine the end moment at wall d. Determine the tangential deviation at point B with respect to point C (t B/C) Determine Өвс A * R 4kN/m 3M
Situation F. The frame is analyzed using Moment Distribution Method 25 kN/m C 75 kN B El = constant E= 200 GPa I= 400(106) mm 3 m 9 m 21. Which of the following most nearly gives the distribution factor at C for member CD? a, 1/2 b. 1/3 с. 1/4 d. 2/3 22. Which of the following most nearly gives the actual moment at C? а. 56.25 KNm b. 133.33 KNm c. 168.75 KNm d. 187.5 KNm 23. Which of the following most nearly gives the vertical reaction at D? a. 70.31 KN b. 133.33 KN c. 91.67 KN d. 4.69 KN 24. Which of the following most nearly gives the horizontal reaction at A? a. 70.31 KN b. 133.33 KN c. 91.67 KN d. 4.69 KN
Draw the M,N,V diagrams of the overhanging beam given in the figure and determine the maximum moment. calculate? A:1 B:7
Draw the shear and bending moment curves for the beam and loadingshown, (b) the maximum absolute value of the shear andbending moment in the beam by the semi-graphical method. F1= 38 kN w1= 14 kN/m
A propped beam shown below is loaded with UDL along its entire span. Determine the following: (Mc) C. a. Determine the reaction (R) b.Determine the end moment at wall d. Determine the tangential deviation at point B with respect to point C (t B/C) Determine Өвс A * R 4kN/m 3M
List down in correct chronological order the necessary water treatment plan processes. Define the purpose of, and describe each process.
A propped beam shown below is loaded with UDL along its entire span. Determine the following: (Mc) C. a. Determine the reaction (R) b.Determine the end moment at wall d. Determine the tangential deviation at point B with respect to point C (t B/C) Determine Өвс A * R 4kN/m 3M
Please use the Moment Area Method in solving this problem.
(4.) Determine the internal normal force, prear force, and bending moment in the beam at point c. 540 N/m Bm
The beam is having a fixed support in one end, and 2 roller support 3m and 7m from the fixed support, respectively. Solve the following: 50kN 25kN/m 3m 2m 2m i.What is the reaction at B? a. 43.50kN c. 76.19kN b. 32.69kN d. 66.23kN ii.What is the reaction at C? c. 17.31kN d. 16.12kN a. 14.77KN b. 18.22kN iii.What is the moment reaction at A? a. 12.75kN-m c. 15.12kN-m b. 23.12kN-m d. 8.44kN-m
Draw the shear and bending moment curves for the beam and loading and the maximum absolute value of the shear and bending moment in the beam by the semi-graphical method. SHOW COMPLEte SOLution. 30 kN 38 kN/m B A D -1.8 m 0.9 m -3.6 m