SITUATION 2: A 30 m tape measured a 412 m distance at a temperature of 520C. The tape is of a standard length at a temperature of 250C. PROBLEM 17: If the coefficient of thermal expansion is 11.6x10-6 m/oC, find the correction per standard length of the a. 0.009396m too long b. 0.009396 m too short c. 0.1290384 m too long d. 0.1290384 m too short REVIES PROBLEM 18: What is the total correction on the measured distance? a. 0.009396m too long b. 0,009396 m too short c. 0.1290384 m too long d. 0.1290384 m too short DILLA RE PROBLEM 19: What is the corrected length on the measured distance? a. 412.009 m b. 411.991 m C. 412.129 m d. 411.871 m

SITUATION 2: A 30 m tape measured a 412 m distance at a temperature of 520C. The tape is of a standard length at a temperature of 250C. PROBLEM 17: If the coefficient of thermal expansion is 11.6x10-6 m/oC, find the correction per standard length of the a. 0.009396m too long b. 0.009396 m too short c. 0.1290384 m too long d. 0.1290384 m too short REVIES PROBLEM 18: What is the total correction on the measured distance? a. 0.009396m too long b. 0,009396 m too short c. 0.1290384 m too long d. 0.1290384 m too short DILLA RE PROBLEM 19: What is the corrected length on the measured distance? a. 412.009 m b. 411.991 m C. 412.129 m d. 411.871 m

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter11: Temperature And Temperature- Related Variables In Engineering

Section: Chapter Questions

Problem 16P

See similar textbooks

Similar questions

I need the answer as soon as possible
Which of the following equations is used to determine the energy loss from transitions and fittings? h Lm = K- 2g D 2g -R,2/351/2 O v = KCR,0.63 s0.54
Prob 3 • A 50 m tape was standardized and was found to be 0.0042m too long than the standard length at an observed temperature of 58 °C and a pull of 15kg. If the same tape was used to measure a certain distance and was recorded to be 673.92m long at an observed temperature of 68 °C and a pull of 15kg, and the coefficient of thermal expansion is 0.0000116/ °C, determine the following: 1. Standard Temperature 2. Total correction 3. True length of the line.
) Given that the thermal conductivity k = 1.8 W/m.°C, and L TT kAq 1 2  Determine the heat-transfer rate (q) from an electronic chip whose surface temperature is 60°C and has an exposed surface area (A) of 50 cm2 and the thickness (L) is 18 mm. The temperature of the surrounding air is 20 °C.
Situation:A 50m steel tape was standardized and supported throughout its whole length and found to be 0.00329m longer at an observed temperature of 41.6 degrees C and a pull of 12 kilos. This tape was used to measure a line that was found to be 683.21m at average temperature of 49 .8 degrees C at the same pull. Coefficient of the thermal expansion in 0.000016m/m degrees C. -DETERMINE THE STANDARD TEMPERATUREa. 35.93 c. 50.76b. 44.63 d. 68.25-WHAT IS THE CORRECT LENGTH OF THE LINE?a. 633.88 c. 638.23b. 663.28 d. 683.32
I need correct and ASAP
QI A) A resistance of moving coil is 122 the moving coil has 100 turns and is 4em long and 3cm wide the flux density in the air gap is 6×10 wh/m. Find the deflection produced by 300 mV if the spring constant is 25x 10 Nm/degree.
Answer number 1 only
Using Moment area method, calculate the horizontal deflection of Joint D in the structure shown in Figure for Question 2 (a) below. I = 1290×106 mm².
Determine the resistance and conductance of 20m 20m of copper wire 2mm in diameter. P=1-72x10²
Do it right !!!
Note: Where appropriate, assume that Young's modulus (E) for steel is 200 KN mm-2 and the coefficient of thermal expansion of steel (a) is 0.0000112 per °C. OWN SOLVING AND NOT CHATGPT FOR UPVOTE