Problem 4.1|A single-phase full-wave uncontrolled bridge rectifier is supplying a highlyinductive load (L/R ratio is very large), the load current is assumed to be smoothand ripple -free. If the supply voltage is 220V, 50HZ, and the inductor loadresistance R=22 N, Calculate:(a)The average output voltage Vác and current Idc-(b) The ms value of the output voltage Vorms and current Ioms -(c) The rms value of the diode current IDrms and the PRV of each diode.

Answered: Image /qna-images/answer/cf5f10f6-bf8d-43f5-b987-582d1b893e8d.jpg

single-phase full-wave uncontrolled bridge rectifier is supplying a h ductive load (L/R ratio is very large), the load current is assumed to be sn d ripple -free. If the supply voltage is 220V, 50HZ, and the inductor sistance R=22 Q, Calculate: OThe average output voltage Vac and current Ide- ) The rms value of the output voltage Vorms and current Iorms - ) The ms value of the diode current Iprms and the PRV of each diode.

single-phase full-wave uncontrolled bridge rectifier is supplying a h ductive load (L/R ratio is very large), the load current is assumed to be sn d ripple -free. If the supply voltage is 220V, 50HZ, and the inductor sistance R=22 Q, Calculate: OThe average output voltage Vac and current Ide- ) The rms value of the output voltage Vorms and current Iorms - ) The ms value of the diode current Iprms and the PRV of each diode.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Determine the ripple factor for the filtered rectifier circuit below when RL= 4KO. Then explain briefly the effect of changing in the RL value on the output waveform. 5:1 Vp= 0.7v for all diodes Vma 100 V f= 60H2 D S0uF
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
In a full wave bridge rectifier, the transformer secondary voltage is 10sinwt. Theforward resistance of each diode is 25Ω and load resistance is 1KΩ.Calculate,i. Imii. Idciii. Pdciv. Pacv. η
/1/A single-phase, half-wave, controlled has a source 220V at 50 HZ and is eding a load R=2002 and L=25 mH, the firing angle a=60° and the current tinction angle ß=225° Determine the average load voltage and current. O Determine the rms load voltage and current. led rectifier the value of the output
iii. For fully controlled single phase bridge rectifier with inductive load (load current is continuous) ,supply voltage 220 V(RMS) and a=30° .The mean value of output voltage is : (a) 150.32V (b) 171.52V (c) 120.98V
A full-wave rectifier produces a 32V peak rectified voltage from a 50Hz ac source. Determine the filter capacitor needed to provide a DC output voltage 24V across a 500 ohm load.
EXAMPLE 3
C4 R1 Vout For the precision rectifier circuit shown in Figure C4 what is the correct operation for the circuit if a Sine wave is 10k D1 R2 LM324 VEE applied to the input signal VIN? Vin D2 10k OUT V3 U1A Figure C4 A. When VIn is negative the circuit operates as unity voltage follower providing an in phase sine wave at VouT. When VIN is positive the circuit conducts but only to one diode drop, B. When VIn is negative the circuit operates as an inverting amplifier providing an inverted sine wave at VouT. When VIN is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, c. When VIn is negative the circuit operates as an inverting amplifier providing an in-phase sine wave at VOUT. When VIn is positive the circuit is driven to very close to zero due to amplifier gain reducing the diode drop voltage, D. When VIn is negative the circuit operates as unity voltage follower providing an inverted sine wave at Vour. When VIn is positive the…
The ripple factor for pure dc is Answer: For the given circuit below, it operates on a peak-to-peak input voltage of 390.1 V, F= 60 Hz household supply through a step-down transformer with turns N1 = 10 and N2 = 1. Silicon diodes are used with a 1 Kiloohms load. Determine the output peak voltage (in volts). D1, D2 AC Input Vsec (Source) .03 D4 Load O 27.31 O 18.11 O 13.93 O 20.91
Design the power supply using diode components. This power supply sholud have 2 outputs. 12Vdc and 5Vdc. Input 240 Vac Supply i. Draw the circuit diagram ii. Bill of material/components that will be used iii. Teh output waveform for each stage
The average (DC) value of a half-wave rectified voltage with a peak value of 200 V is: a. 63.7 V b. 127.3 V c. d. OV 141 V 2. Voltage regulation is determined by: a. load current b. Zener current and load current c. changes in load resistance and output voltage d. changes in no-load voltage and full-load voltage When a 60-Hz sinusoidal voltage is applied to the input of a full-wave rectifier, the output frequency is: a. 120 Hz b. 60 Hz c. 240 Hz d. 0 Hz
Assume AT the output of a filtered half wave rectifier circuit a series resistor RS of 4.2kohm together with a shunt connected 54v zener diode is now connected as a simple regulated circuit. The zener is connected in parallel with load RL of 11.9 kohm. When the input mains voltage flutes at various parts of day the max DC voltage appearing across the capacitor is 120 V and thefor the above zener maximum voltage is 80 V. Determine the load current in mA flowing through the load,