simply supported beam 10 m long has an overhang of 1.1 m at the left support.  If a highway uniform load of 12.02 kN/m and a concentrated load of 194 kN, passes thru the beam, compute the maximum positive shear (kN) based on influence line for maximum shear at mid span.

Q: Draw the SFD and BMD for the beams loaded as shown in  Calculate the position and magnitude of ma

A: Given:

Q: I need working with an answer and an explanation of the concept on hand please. GIVEN: Beam as…

A:

Q: A beam is of T section, as shown in fig. The beam is simply supported over a span of 4m and carries…

A: Given Data  Length of the span, L=4 m UDL, 4.7KN/m

Q: INCLUDED L 300kg W = 70 1 ↓ LEQUINED: 0 kg 61 50! C OLVE F L L 2m 50/5/m W = jooks 6 M = 100/g-m…

A:

Q: Draw shear force digam and bending moment digram for the following beam 2.0 kips / ft A В 15.0 ft…

A: Let RA and RB are reactions at A and B  By using law of equilibrium RA+RB =12  Moment at point A is…

Q: Figure 14.22 Full Alternative Text 14.23 If the allowable shear stress is 100 MPa, calculate the…

A: Givenallowable shear stress τ = 100 MPa = 100 N/mm2Beam specification of W460 x 60

Q: 17 KN i. 3000 12 KN 2000 1 6000 4 kN/m B/ TITI 1000 19 KN

A:

Q: Problems 6-5: Express the internal shear and moment in the cantilevered beam as a function of x and…

A: Given : The free body diagram is,

Q: calculate the beanding moment and shear force diagrams

A:

Q: A continuous beam has three equal spans of 20 ft eachand a uniformly distributed load of 800 lb/ft…

A: Draw the free body diagram of the continuous beam.

Q: Without writing shear and moment equations, draw the shear and moment diagr ams for the beams…

A:

Q: Draw shear force digam and bending moment digram for the following beam 300 N 500 N 800 N to to 0.5…

A: A cantilever support will exert horizontal component of reaction, vertical component of reaction and…

Q: Four wheel loads rolls as a unit across a 18-m span. The loads are 50 kN, 30 kN, 20 kN, and 10 kN…

A:

Q: SKETCH SHEAR / MOMENT DIAGRAMS FOR THE SITUATIONS BELOW, ASSUME EI = CONST. FOR EACH BEAM A 10 2…

A: Let's start with the calculations to determine the reactions at supports A and B, and then proceed…

Q: **** A wood beam carries a bending moment of 15 500 lb-in. It has a rectangular cross- section of…

A:

Q: other. A twisting moment of 30,000 lb-in. is applied If E-30x10 psi and G-12x10 psi, compute the

A: Given that ,

Q: Select the lightest-weight wide-flange beam with the shortest depth from Appendix B that will safely…

A: Given data: Allowable bending stress, σallow = 24 ksi Allowable shear stress, τallow = 14 ksi…

Q: An example of a liquid lubricant is crude base that is introduced between two contact surfaces to…

A: The basic purpose of the lubricating any moving part is to reduce the friction between the parts and…

Q: Example 10.2. After solving for the support reactions, calculate and then draw the shear and bending…

A: Let RA and RB are the reactions at A and B  By using law of equilibrium  ΣFy = 0 RA +RB = 60 Taking…

Q: For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the…

A: The values are Ma=9 kNm, wo=19.8 kN/m, Lab=1.1 m , Lbc=2.7 m, EI=1270 kNm2.

Q: the carrying cost

A: Given; Company has annual demand of, 1000 units,  ordering  cost =Rs 100/ ordercarrying cost = Rs…

Q: Abeam with a rectangular cross section is simply supported and loaded at its center with a force P.…

A:

Q: Compute moment strength (capacity) of the beam cross section given. Tension reinforcement area:…

A:

Q: A roller 30 lb/ft * B hinge

A: Given  beam

Q: 10. A 30m long horizontal beam carries a uniformly distributed load of 1 kN/ m on the whole length…

A: To determine:Position of second the support for minimum bending moment.SFD and BMD

Q: Floor joists 64.8 mm wide by 106 mm high, simply supported on a 4.3 m span, carry a floor loaded at…

A: Horizontal supports that go from wall to wall, wall to beam, or beam to beam are known as joists.…

Q: Exercise 7.4 A 5-m-long beam is hinged at end A and roller supported at end B carries udl of 5 kN/m…

A:

Q: Problems 7-5: If the wide-flange beam is subjected to a shear of V = 30 kN, determine the maximum…

A: Given data:   V= 30 kN = 30000 NWe have to determine the maximum shear stress of the beam. So first…

Q: 1. A 12 m cantilever beam has a uniform load of 1.5 kN/m extended from fixed end up to 4 m and a…

A:

Q: 1. Draw shear and moment diagram for the overhanging beam shown below, and then draw the elastic…

A: Given: Point load at C=3 kip Point load at 6 ft distance from left end=6 kip Uniform distributed…

Q: The allowable tensile bending stress is 6700 psi and the allowable compressive bending stress is…

A: The allowable tensile bending stress is The allowable compressive bending stress is

Q: for the beam shown below. Hinge- 10 m BC +sm+ 25 kN/m -15 m DO E -5 m- Hinge -10 m-

A:

Q: Find the section modulus for a beam of rectangular beam of breadth 45 mm, depth 50mm. The section…

A: We have to determine section modulus of beam

Q: Problem 5 The beam shown below is subjected to unfactored service live loads, PL and w. Neglect the…

A:

Q: A vehicle and trailer combination cross a 12-meter bridge with axle loads of 10, 20, and 30 kN…

A:

Q: nd bending moment diagram for beam loadi

A: given:

Q: 100 lb 100 lb 300 lb/ft 200 lb/ft A * 5' – 0" 5' - 0" | 13.40

A: Solution is attached below:

Q: W Given a simply supported beam with length of 12 feet and a uniformly distributed load of w =…

A:

Q: 2. FROM THE GIVEN BEAK COMPUTE THE FF- a REACTIONS @ A B b. SHEAR AD MOMENT AT C DRAVW 7HE SHIEAR 3…

A: Hi. as you have posted multiple questions and have not specified which question needs to be solved,…

Q: Select the lightest-weight wide-flange beam from Appendix B that will safely support the loading.…

A: Consider the free body diagram shown below for the given beam.