Show the possible arrangement of fluid position in the following pressure measuring devices under specified conditions. 1. Piezometer connected to the side of a water tank containing water up to 2 m depth. 2. Manometer connected to a water tank filled up to lm and is open to atmosphere. 3. Differential manometer connected to two tanks of 2 m and 1 m diameter filled with water and petrol respectively up to the same level and both are open to the atmosphere. 4. Piezometer with negative pressure. 5. Manometer connected with empty water tank.

Show the possible arrangement of fluid position in the following pressure measuring devices under specified conditions. 1. Piezometer connected to the side of a water tank containing water up to 2 m depth. 2. Manometer connected to a water tank filled up to lm and is open to atmosphere. 3. Differential manometer connected to two tanks of 2 m and 1 m diameter filled with water and petrol respectively up to the same level and both are open to the atmosphere. 4. Piezometer with negative pressure. 5. Manometer connected with empty water tank.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Fluid Mechanics , i need solutions in 15 minutes please. MCQ/Find the capillary rise (h) in the tube…

Q: 2. Consider a venturi meter having a throat diameter of DB = 6 inches. The deflection of mercury in…

Q: 4. An inclined tube manometer has the area of the reservoir as 277 mm² and diameter of the inclined…

A: Question is based on manometer tube . Area of reservoir , diameter of inclined tube, Specific…

Q: Show the possible arrangement of fluid position in the following pressure measuring devices under…

A: Asked: Show the possible arrangement of fluid position in the following pressure measuring…

Q: pressure gauges to show the same r

A: Diameter of large section is d1= 300mm or .3m Discharge at gauges = .4m3/sec Datum head of smaller…

Q: A clean circular glass tube is to be selected in the design of a manometer to measure the pressure…

A: Given data Specific gravity Surface tension Cappilary rise Angle of contact is zero for glass and…

Q: . Determine the velocity at the center of the pipe.

A: Level of water in pitot tube from top surface=20 cm Level of water in piezometer from top surface=35…

Q: (Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the…

A: Required : Manometer readings h and H given in the diagram.

Q: A differential manometer is connected at the two points B and C in of two pipes as shown in Figure…

A: Pressure at point B (Pb)=200kPa Difference in mercury level inside the U tube manometer (h)=30cm…

Q: 2.) A liquid having a Reynolds number of 1500 flows thru a 200-mm diameter pipe, 220m long. The head…

Q: 14 in, da measures 3 in. If SGmercury is 13.55, a) calculate the pressure difference (in psi)…

Q: 6- Determine the absolute pressure in a pipe which is connected to a simple U-tube manometer, the…

Q: Oil of specific gravity 0.82 flows through an orifice at the vertical side of a closed cylindrical…

Q: pressure of air in the pipe

A: P=ρgh at any point Given h1=0.33mh2 =0.36mh3 =0.20m h4=0.50m h5 =0.10m h6 =0.30

Q: A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A…

A: Given Specific weight of Gage fluid = 112 lb/ft3

Q: . The value of unknown pressure Pis

A: Given data, The pressure gauges G1 and G2 installed on the system showpressure of, PG1=5.00 bar…

Q: Explain the Menard-type pressuremeter: Components and operating principles.

A: A pressuremeter is a device that is used for determination of the relations of stress strain of…

Q: 3. Oil of Gs=0.80 is flowing in a pipe 8 inches diameter with a mean velocity of 12 ft/sec. The…

Q: Figure 1 shows the manometer apparatus with different fluids. mercury and oil are 13.56, and 0.9…

A: Given data in question Specific gravity Depth Area ratio Volume x = Volume y To find out Delta Z…

Q: Water is flowing in a pipeline, the pressure in the inlet pipe is 20 kPa there is a gradual decrease…

Q: A Differential manometéř Is ne points A and Bat the centre of two pipes. he pipe A(left limb)…

Q: A U-tube manometer is connected to a closed tank as shown in the figure below. The air pressure in…

A: Solution: a) Depth of oil Z PA=γoilZ+Pair2×144=54Z+0.5×144Z=4 ft

Q: mpt in progress A U-tube manometer is connected to a closed tank as shown in the figure below. The…

Q: SUBJECT IS HYDRAULICS SHOW DETAILED AND COMPLETE SOLUTION USED 3 DECIMALS FOR THE FINAL ANSWER A…

Q: A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A…

A: Specific weight of fluid in manometer, γm=112lbft3The pressure drop between two taps, δP =0.7lbin2

Q: 6. In the manometer shown at right, containing mercury (s.g.-13.6) from A to B, and oil (s.g.=0.85)…

A: Given Data Determined the pressure at point C.

Q: Show complete solutions and figures. The shown tank with an attached manometer contains water unit…

Q: 7. A simple U-tube manometer can measure negative gauge pressures.

A: A simple U-tube manometer can measure negative gauge pressures. This is true statement

Q: For the following inverted manometer setup, if the pressure at x is 200 kPa, what is the pressure at…

Q: a pipe has a pressure of 4000 pascal and is connected to a 36 degree inclined single column…

A: We will take pressure at top level of mercury in reservoir same from both left and right side.

Q: A differential manometer is attached to a pipe, as shown in the figure. Calculate the pressure…

Q: 9. For dynamic fluid motion in a pipe, the pressure measurement cannot be carried out accurately by…

Concept explainers

Pressure and Stress

Question

Show the possible arrangement of fluid position in the following pressure measuring devices under
specified conditions.
1. Piezometer connected to the side of a water tank containing water up to 2 m depth.
2. Manometer connected to a water tank filled up to lm and is open to atmosphere.
3. Differential manometer connected to two tanks of 2 m and 1 m diameter filled with water and petrol
respectively up to the same level and both are open to the atmosphere.
4. Piezometer with negative pressure.
5. Manometer connected with empty water tank.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

(Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the pipe contraction shown in the figure below. The flowing fluid is water, and viscous effects are negligible. Determine the two manometer readings, h and H. V=2.2 ft/s h= H= 6.3 in. Air SG= 1.10 ft •ft H 3.5 in. h
Subject: Hydraulics
The Menard-type pressuremeter consists of the probe. Describe in detail about probe.
(Bernoulli/continuity/Pitot tube) Two Pitot tubes and two static pressure taps are placed in the pipe contraction shown in the figure below. The flowing fluid is water, and viscous effects are negligible. Determine the two manometer readings, h and H. V=1.7 ft/s h = H= 6.4 in. Air ↓ SG= 1.10 ft ft TH 3.8 in.
Show the possible arrangement of fluid position in the following pressure measuring devices under specified conditions. 1. Piezometer connected to the side of a water tank containing water up to 2 m depth. 2. Manometer connected to a water tank filled up to 1m and is open to atmosphere. 3. Differential manometer connected to two tanks of 2 m and 1 m diameter filled with water and petrol respectively up to the same level and both are open to the atmosphere. 4. Piezometer with negative pressure. 5. Manometer connected with empty water tank.
Flow measurement.
A flow rate measuring device is installed in a horizontal pipe through which water is flowing. A U-tube manometer is connected to the pipe through pressure taps located 3 in. on either side of the device. The gage fluid in the manometer has a specific weight of 112 lb/ft3. Determine the differential reading of the manometer corresponding to a pressure drop between the taps of 0.5 lb/in². h = ft
1. Figure 1 shows the manometer apparatus with different fluids. It is given that the specific density of the mercury and oil are 13.56, and 0.9 respectively. Solve, a. The liquid level, Az when the area of the reservoir on the left lim b of the manometer is 100 times the area of the manometer tube in right limb. The volume X is equal to Volume Y. b. The pressure at point A. Oil Volume Y 45cm 18cm Mercury Az Volume X
Current Attempt in Progress A U-tube manometer is connected to a closed tank as shown in the figure below. The air pressure in the tank is 0.50 psi and the liquid in the tank is oil (y = 54.0 lb/ft³). The pressure at point A is 2.00 psi. Determine: (a) the depth of oil, z, and (b) the differential reading, h, on the manometer. (a) z = (b) h = ft ft Air Oil SG = 3.01 2.0ft + Open h