Show complete solution in finding the d10, d30 and d60 and also graph using the graph presented Unified Soil Classification SystemProblem Set No. 6Sieve No.DiameterPercent Finer(mm)2. The table below the laboratory results of thesieve analysis of a sample. Plot the grain sizecurve of the soil using your printed Grain SizeCurve. Determine the following:44.759082.3864102.0058200.8435a. Determine the nearest value of effective size.22b. Determine the coefficient of uniformity, Cc. Classify the soil according to USCS.400.42600.25151000.14910Showyour complete solution.2000.0754 1009080* 706030100.0010.010.15020Percent Passing, %

As only D10, D15 and D60 are asked only they are found along with coefficient of uniformuty and…

Answered: Show complete solution in finding the…

Engineering

Civil Engineering

Show complete solution in finding the d10, d30 and d60 and also graph using the graph presented

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Using conjugate beam method determine the value of E18 at 2 ft from R2. Ans. ElōB = 853.32 lb-ft3…

Q: Q2: - A tape 100m long. it's cross sectional area in 0.0585 cm, the apparent length of which was…

A: Length L = 1500 m = 150000 cm Area A = 0.0585 cm2 Standardised pull Ps = 6.75 kg Actual Pull P =…

Q: Only answer A. Explain why the obtained answer makes sense.

A: This question is related to the Strength of the material from Civil Engineering. As per question…

Q: A beam having a tee-shaped cross section is subjected to equal 18 kN-m bending moments, as shown.…

Q: Slope deflection to determine the forces reactions

A: Sign convention : assuming clockwise moments as positive(+) and anti-clockwise moments as…

Q: y 53 mm 85 mm 25 mm 57° 25 mm - b 65 mm

Q: SIZE (mm) WEIGHT RETAINED 0.25 18.96 gms. 0.149 33.18 0.074 45.03 0.052 54.51 0.02 42.66 0.01 11.85…

Q: From the figure shown, determine the following: y L, h, L2 L4 CE h, h, ha he hs he Distance of the

A: Determine centroidal distance y from x axis

Q: 40KN A 4m 100KN- D E

Q: The roller at A is moving upward with a velocity of A = 2 ft/s and has an acceleration of a = 6…

A: In kinematics, if one object's motion depends on another object's motion, then it is called absolute…

Q: Determine the spacing of vertical stirrups near the left support of the "L"(m) beam loaded as shown…

Q: ++ 0.3 m S2 3.15 m ++ 0.3 m B. 7.0 m ++ 0.3 m 1.2 m 0.3 m 4.2 m 0.3 m 1.4 m 300 mm #+ +1 140 mn 360…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Using graphical method, find the resultant and its inclination with the x-axis as shown in the…

A: Note: Hi! Thank you for the question As per the honour code, We’ll answer the first question since…

Q: (c) A steel bar has three segments with 600 mm long which is subjected to the different loads as…

A: (i) Determine stress in each section. (ii) Calculate the total elongation (extension) in the bar.…

Q: QUESTION 3 A plank L m long is placed in a horizontal position with its ends resting on two inclined…

Q: Determine the resultant couple moment acting on the beam. (Figure 1)

A: Solution: Considering the diagram:

Q: ate the computational degrees of free system. LL F H B E D types of

Q: Solve for the critical value of P under LRFD Method. Use Fy = 275MPA, Fu = 40OMPA and %3D thickness…

A: Given data:- fy = 275 MPa fu = 400 MPa Thickness = 12 mm To find:- The critical value of P ?

Q: PLEASE INPUT THE LAST 4 DIGITS OF YOUR STUDENT NUMBER HERE 7 3 4 3 L, 600 mm %3D h, 65 mm L2 170 mm…

A: To Determine Distance of Centroid from x-axis.

Q: A solid cone was found floating in water (SGwater= 1.0). The cone may float in two different…

Q: Im 2m

Q: ■ Determine the maximum T of the structural arrangement as shown below (S275). T 25 25 25 25 25 水 41…

Q: A cylinder with a weight of 800 lb is held in equilibrium by three ropes. The hooks are arranged in…

Q: [1 2] 2 4 1 2 3 9 E = 1 2 9 41 F [4 2 1 7

Q: Derive expression for mode shapes and frequencies of a uniform cantilever beam and determine the…

A: Mode shapes: The special initial displacements of a system that cause it to vibrate harmonically…

Q: True or false F. A structural engineer is a civil engineer who oversees the design and…

Q: What

Q: omn ample-2 For measuring the area of a figure using planimeter, the as placed outside and the…

Q: Calculate unknown force

A: This question is from solid mechanics

Q: Q D1 D2 D4 L1 D3 L2 L4 Find out the following? Case 1: Major Losses only H = Case 1: Minor Losses…

Q: The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting…

A: Given : To Find :

Q: 5. Cross ties are used if the distance between a bar and the corner bar is greater than ... а. 100…

A: Cross ties are used when the distance between a bar and corner bar is greater than 150 mm. Cross…

Q: Locate the centroid y of the beam's cross-sectional area. Take a = 45 mm (Figure 1) Express your…

A: Find centroid :y=A1y1+2A2y2A1+2A2

Q: Consider the following free-body diagram of a beam. 200 N 100 N 200 N 100 N-m B 2 m 3 m 3 m 2 m What…

A: Free body diagram of the Beam:-

Q: ose that A 3.2 m. (Figure 1) Determine the magnitude of the resultant force of the two forces acting…

A: Given : To Find : FR , Alpha , Beta and Gamma?

Q: Take that a = 38 mm. (Figure 1) Part A Determine the moment of inertia of the beam's cross-sectional…

A: for flange section b1=6a and depth d1=afor web section width b2=a and depth…

Q: Consider the flow of a viscous fluid parallel to a plate. You want to check the shear effort on the…

Q: QUESTION 3 A plank L m long is placed in a horizontal position with its ends resting on two inclined…

Q: The T-shaped column shown reinforced with 4-28 mm diameter bar with fy = 414 MPa and f'c= 27.6 MPa.…

Q: QUESTION 3 A plank L m long is placed in a horizontal position with its ends resting on two inclined…

Q: This is an exercise to illustrate the effects of mesh refinement on a 1-d rod. To estimate the…

A: Do = 3m R 1.5m α = 0.3 So, d = 0.3x3 = 0.9m r = 0.45m L= 5m

Q: An experimental device imparts a force of magnitude F = 48 lb to the front edge of the rim at A to…

A: Given data Find moment about O and B. (Counterclockwise positive) Find d distance from O to C…

Q: A throat plate is a component that can be found in sewing machines. Shown in the figure is a…

Q: Question 1: 1. The figure shows two steel shafts connected by a steel pipe with interference.…

A: Solution;

Q: The 90 Ib force of Figure is the resultant of three coplanar forces and a couple Determine the force…

A: Given 90 lb force is the resultant of three coplanar forces and a couple. Required The unknown…

Concept explainers

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land. Zoning is done or can be understood with the help of a site plan.

Question

Show complete solution in finding the d10, d30 and d60 and also graph using the graph presented

Unified Soil Classification System
Problem Set No. 6
Sieve No.
Diameter
Percent Finer
(mm)
2. The table below the laboratory results of the
sieve analysis of a sample. Plot the grain size
curve of the soil using your printed Grain Size
Curve. Determine the following:
4
4.75
90
8
2.38
64
10
2.00
58
20
0.84
35
a. Determine the nearest value of effective size.
22
b. Determine the coefficient of uniformity, C
c. Classify the soil according to USCS.
40
0.42
60
0.25
15
100
0.149
10
Show
your complete solution.
200
0.075
4

100
90
80
* 70
60
30
10
0.001
0.01
0.1
50
20
Percent Passing, %

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The simply supported concrete beam shown in the figure has an effective depth of 600 mm and a sectional width of 300 mm. If fc= 28 MPa and fy=420 MPae then :answer the following questions: 1-he spacing of Ø10 mm stirrups at the critical section from the face of support A equals =, mm (round to * the nearest integer number 2-The spacing of Ø10 mm stirrups at the critical section from the face of support B equals. .mm (round to the * nearest integer numbe 100 kN/m A B 6 m 8 m
I am undure of how to solve for Iv and Iuv in this case how do I do this?
Solve for the critical value of P under LRFD Method. Use Fy = 275MPA, Fu = 400MPA and thickness equal to 12mm. 80 60 60 80 60 60 80 60 60 100 mm mm mm mm mm mm mm mm mm mm 80mm 180 280 160 440 25ø 400 G0mm 400 320 360 180 28Ø 250 60mm 250 120 100 280 140 360 220 320 480 80mm P.
urces Consider the force shown in (Figure 1) Figure F-750 N 10f1 Part A Express the force as a Cartesian vector. Enter the components of the force separated by commas. Express your answers in newtons to three significant figures. F.F.F.- Submit Provide Feedback VAZ Ivec Previous Answers Request Answer N Next >>
Make 2 free body diagrams
i need the answer quickly
ES IS lio cuts ebsite ahman [² Question 14 of 25 A lead cube has a total mass of 80 kg. What is the length of its sides if SG = 11.3? Select the correct response: Slunef 18.23 cm 19.2 cm 15.29 cm 12.32 cm 20.3 cm < Previous CHAPTER bar CHAPTER 213 ppt CHAPTER 1(4)(2).ppt
Determine (a) the x, y, and z components of the 900 N force, (b) the angles θx, θy, and θz that the force forms with the coordinate axes. Note: Please show the complete solution for the problem together with the free body diagram in resolving the force into its components. As it is needed for my review. Thank You!
Need in 30mins
Hy Experts , I need help Please solve this question
Solve for the critical value of P under LRFD Method. Use Fy = 275MPA, Fu = 400MPa and thickness equal to 12mm. 80 60 60 80 60 60 80 60 mm mm 100 mm mm mm mm mm mm mm mm 80mm 180 280 160 440 250 400 60mm 400 320 360 180 280 250 60mm 100 280 140 360 20 480 80mm