Show all the steps along with the proper SI Units. 1. Referring to the figure below, draw the free body diagram of the box and find both the tension in the cable that is holding a box resting on a rough inclined surface and the force of the surface on the box. (Friction force =0.07 KN). 33.2kg 315

Q: Define CMM.

A:

Q: 20 40 t. 20 40 30 40 20 to 30

A: Gross area of the column =area of concrete + area of reinforcementGross area of the first column…

Q: How many "varas" are there in a single ruler measurement?

A: A single ruler is the standard ruler which has measurements given in inches or mm. It is used to…

Q: show the integration process

A: To show the integration process

Q: Could you show the calculations for the table

A: The discharge through the section = Q = 100, 150, 200, and 250 cfs The slope of the section = S =…

Q: What is binder?

A: A binding agent, or binder, is a medium that is used as a way of supplying structural support to…

Q: Define Decimeter.

A: Decimeter: It is a length unit in a metric system. which is equal to a tenth of a meter.

Q: What is Structural Plan?

A: A structural plan is a plan used as a framework to take up the land development or renovation of an…

Q: What do you mean by the slice action and how many slice operated dimensions are used?

A: #1What do you meant by the slice action?? A slice operation is defined as the particular filtration…

Q: Define Peclet number.

A: It is defined as the ratio of the rate of advection of a physical quantity by the flow to the rate…

Q: What are the characteristics of ordinal level measurement scale variables?

A: Data provided :  Ordinal level measurement scale variables    To determine : The characteristics of…

Q: how did you get 1.5 for the first part

A: In the original question it is stated that Vmax=2 Vmin In the solution, the following is given.…

Q: Define integer ambiguities.

A: Answer The integer ambiguities are used in GPS & GNSS surveys.

Q: What are Cole values

A: Solution: COLE stands for The Coefficient of linear Extensibility.  It is used to measures the soil…

Q: What is a box model? Give the equation to represent box model.

A: The Urban air quality models has been called box models. The Figure is a schematic graph of a box…

Q: 10 25k 10'

A: The below cantilever beam is given;

Q: What is the area of 6 #8 bars in inches^2? Give an answer to two decimal places.

A:

Q: what is ytm

A: There are different type of the calculation done in the funds. The funds can increase or decrease…

Q: what is america door panel and it size

A: Solution: The most common front sizes of the door in American houses are 36 inches wide and 80…

Q: whered did you get .2?

A: I'm proceed according to solution The difference of maximum value and minimum value of weight is 0.2…

Q: What is the difference between interval and ratio level measurement scales?

A:

Q: usescale (1/1) draw the front Section view in mides pan and the side Sectional Vien middles pan for…

A: Front Sectional View: The front sectional view is the view of the object done by taking a section…

Q: Renolds number, define it?

A:

Q: How are units converted using dimensional analysis?

A:

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: some examples of the term OFFSET

A:

Q: Explain the Modified Mercalli scale.

A: The effect caused on the surface of the earth due to an earthquake is known as the intensity of the…

Q: What is sumps?

A: Sump collects building up underground water so that it can be pumped aside from a finished building…

Q: * To draw an arc angle between two intersecting lines Fillet O Block O Trim Chamfer O If we want to…

A:

Q: Is "Object-Oriented" a term that may be used without any problems? The creation of software that…

A: "Object-Oriented" is a widely accepted and established term in software development that refers to…

Q: Defline APP.

A: Basic Concept Introduction- APP- It is the short form or abbreviation for the application.

Q: Differentiate initial and boundary value problems.

A: Both type of problems are similar to each other except for that boundary value problem have…

Q: How is the dimension paper used to compile an accurate Bill of Quantities??

A: Dimension paper is used in taking off which refers to the process which identifies elements of…

Q: Define Relative precision.

A: Relative precision:

Q: What are Quantity Variations?

A:

Q: What is Micropiles?

A: - A Micropile is a type of friction pile having diameter less than equal to 305 mm which can be…

Q: Define a logic loop.

A: The loop means a continuous order of formations which can repeat the work until a certain…

Q: please explain where 1/32 come from?

A: Given, D = 0.2 in τmax = 20 ksi G = 12 x 106 psi

Q: Define Relative Density.

A: Relative density or specific gravity:

Q: The state of stress at a point in a member is shown on the rectangular stress element in (Figure 4)…

A: 1. Deactivate the voltage source (V1):Set the voltage source V1 to zero (0 V). This means the…

Q: Define the following words Tesserae Kline  Klismos Chai

A: These three terms give various elements that are important in design and art. Learning these will…

Q: Explain the Importance of Auto CAD.

A: INTRODUCTION: AutoCAD is used by architects and drafters to create plans for buildings, bridges, and…

Building codes

Building codes are the set of norms that contain all the standards for the construction of all the building and non-building structures. It is essential to follow the guidelines given in the building codes to get the project approved by the local authorities. The engineers, architects, contractors, and all the people involved in construction activities are obligated to refer to the building codes before performing any construction activity. In the United States of America (USA), The I-Codes, which are the International Building Code (IBC) or International Residential Code (IRC), electrical codes, plumbing codes, and mechanical codes are the model codes adopted. These model codes are updated after every three years.