shoreline ware crest 20°

Q: What is the total land area?

A: Solution Point  Distance Bearing Azimuth Latitude Departure DMD Double area 1    2 74.51 N 830…

Q: 1. Determine las coordenadas del centroide de la siguiente figura. 4a 3a

A: solved

Q: The horizontal angle of a line was measured 4 times in the field and the results are as follov 156°…

A: Most probbale value is average of the data Average =sumn

Q: For true difference in elevations between two points 'A' and 'B', the level must be set up * At any…

A: A level is used to know the difference in elevation between two points A and B

Q: From the given data of a closed traversed, Line Bearing Distance AB S. 8deg. 51' W. 126.90m. BC…

A: Given data,

Q: Given the following coordinates for two points A and B, A (xA 680,50m; yA = 750,40m); B (xB =…

A: A grid bearing is generally a method used to measure in relation to the fixed horizontal reference…

Q: Compute the latitude for the following line: N 05⁰-40'-57" W 268.74' + 26.6095 O-267.4194 O-26.6095…

A:

Q: 5. Calculate the lengths of the two missing sides and the area of the following parcel' 117 17' 30…

A:

Q: Determine the length and direction of a line that runs through F and divides the tract into two…

A:

Q: Corrected Latitude The initial latitude for 'S 30°-51'-47" E 249.50' is: -214.1698 The residual for…

A: Surveying : a field of practical mathematics dealing with calculating the area of any piece of the…

Q: LINE LENGTH, m BEARING АВ 28.612 N 19° 54' 47.27" W N 71° 55' 22.54" E S 62° 28' 13.34' E S 25° 37'…

A: LINE BEARING LENGTH (m) Latitude=lcosθ Departure=lsinθ AB N19°54'47.27''W 28.612 26.901…

Q: Contour interval - 20 meters Figure above is a water table contour map 1- Mill River generally flows…

A: The correct direction of mill river is North East direction according to the given contour map.

Q: ?What is the elevation of point BM1 in the below table if you know that the elevation of BM2 is…

A:

Q: What is the total land area? N. 83 deg 46'E.,74.51 m. to point 2; N. 85 deg 30'E.,15.92 m. to point…

A: Solution   Point  Distance Bearing Azimuth Latitude Departure DMD Double area 1    2 74.51 N…

Q: For true difference in elevations between two points A and B, the level must be set up at any point…

A:

Q: situation 21 Another closed parcel was surveyed by the same party who laid out the lot in situation…

A: First we will convert all bearings into WCB and then we will take sum of latitudes and departures as…

Q: What do you mean by? AEW , sMTI

A: AEW :- Airborne Early Warning An airborne early warning is defined as a system in an airborne radar…

Q: What is rock's minimum principal stress? (A) 72.33 kPa (B) 72.53 kPa Ⓒ 72.23 kPa (D) 72.63 kPa

A: Using formula

Q: MEASURING ANGLES WITH TAPE. The measure 1063.55, 1840.33, and 1325.05 m. sides of a triangle…

A:

Q: 1.In item No. I what is the length of m or AP? a) 4,226.67m     b) 4,567.34                  c)…

A: To find length of BP and AP

Q: COURSE LENGTH (m) BEARING / AZIMUTH АВ 110.80 32°27' BC 83.60 unknown CD 126.90 188°51' DE unknown…

A:

Q: What is the value of double area if the value of latitude of and DMD is +89.26 m? O a. 21305 sq. m O…

A: Latitude of A=235.67m DMD=+89.26m To find value of double area

Q: Dist. (m) Mean Dist. (m) Line Azimuth Bearing Latitude Departure from South 1-2 27.35 171° 18' N…

A:

Q: Does the image below depict a Cut or a Fill from the construction stake to the back of curb?

A: This question is from Surveying.

Q: a) The length of course DE, in meters, is b) The bearing of course BC is c) The perimeter of the…

A: For the given data, the latitude and departure are found out below after converting the given…

Q: what is the value of the back bearing 50° 25' 20

A: Back Bearing (B.B)-                                 Back bearing is the bearing of the line in the…

Q: What are CORS and HARN stations?

A: Introduction : NOAA/National Geodetic Survey manages the NOAA Continuously Operating Reference…

Q: why is it important to conduct  cross section level for a irrigation canal ?

A: Cross section of an irrigation canal: Components of cross-section: Side slopes Berms Free board…

Q: From the given traverse result: Lines Bearing Distance…

A: Closed traverse ABCDEA is given where bearing of line DE and EA is missing. It has been asking to…

Q: How can we calculate mean free path ?

A: Brief concept- Mean Free Path- When a molecule collides with another molecule then in between the…

Q: B 5,000 t A 4,800 ft the map of water table above has contour interval (Ah ) =

A: Contour interval (∆h) = elevation difference between two contour line

Q: How many miles is T2S, R3E from the Principle Meridian? From the Tallahassee Baseline?

A: This question is related to the US Government Land Survey Methods. In such a system the north-south…

Q: The elevation of A on the ground surface is 134.78m while the elevation of another point B on the…

A: Elevation of point A=134.78m Elevation of point B= -78.9m

Q: 7.321 meter as yards

A:

Q: 26.5* Two level sections 75 ft apart with center heights 4.8 and 7.2 ft in fill, base width 30 ft,…

A: Given data- B= 30 ft L =75 ft Slope = 2:1 Find out - Volume of cross section ?

Q: Calculate the area of the land whose coordinates are given below. (9, 26) (25, 19) 21 31 (12, 11)

A: As the given land is in the shape of a triangular shape. The area of a triangle is described as the…

Q: Cadasteral aruey س لععلمافر relaled uth boundary g field.

A: Cadastral survey is a type of survey . This survey is done to find the public  land boundary as well…

Q: S30°47'19"W N79 15'12"E

A:

Q: a) What is the distance to the rock from points "A" & "B"? b) What is the perpendicular distance of…

A:

Mechanics of Solids

It is the study of the behavior of solid materials, their characteristics under various circumstances such as variation in external forces, temperature, and other internal factors. It is one of most important study in the field of engineering science, especially chemistry and mechanical engineering. In rigid body, the idealization of the solid body in which deformation is neglected. Deformation is known as the force acting on the solid state system which exerts change in its shape of the body but it continues to be at rest or in a uniform motion but it cannot accelerate. But those solid systems do have elasticity, compressibility and can be bent. This field is very vast since there are wide range of materials around us.