Please explain where the results in the table came from Shear rate (Seconds-1)Shear Stress (dynes/cm²)20113015.24019.15022.96026.5Draw the log-log table of shear rate and shearstress as follows: -Shear rateShear StressY (s-1)log (7)T (dynes/cm²)log (7)202.9957112.2979303.401215.21.7213403.688919.12.9497503.912022.93.1311604.094326.53.2771Step2b)(1) Plotting the log-log paper of shear stress andshear rate as shown below,(3.912, 3.121(3.401, 2.721)(4.094, 3.277)(3.689, 2.95)(2.996, 2.298)?

Shear stress and shear rate values are used to determine the viscosity of fluid . These values will…

Shear rate (Seconds¬1) Shear Stress (dynes/cm²) 20 11 30 15.2 40 19.1 50 22.9 60 26.5 Draw the log-log table of shear rate and shear tress as follows: - Shear rate Shear Stress (dynes/cm²) log (T) 2.2979 log (7) 20 2.9957 11 30 3.4012 15.2 1.7213 10 3.6889 |19.1 2.9497 50 3.9120 22.9 3.1311 50 4.0943 26.5 3.2771 Step2 1) Plotting the log-log paper of shear stress and hear rate as shown below, (3.912, 3.121) (3.401, 2.721) - (4.094, 3.277) (3.689, 2.95) (2.996, 2.298)

Shear rate (Seconds¬1) Shear Stress (dynes/cm²) 20 11 30 15.2 40 19.1 50 22.9 60 26.5 Draw the log-log table of shear rate and shear tress as follows: - Shear rate Shear Stress (dynes/cm²) log (T) 2.2979 log (7) 20 2.9957 11 30 3.4012 15.2 1.7213 10 3.6889 |19.1 2.9497 50 3.9120 22.9 3.1311 50 4.0943 26.5 3.2771 Step2 1) Plotting the log-log paper of shear stress and hear rate as shown below, (3.912, 3.121) (3.401, 2.721) - (4.094, 3.277) (3.689, 2.95) (2.996, 2.298)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Please solve full SOLUTIONs. One page don't do it in steps thanks
multiply the numbers 56 inches* 9
Locate the center of mass of the homogeneous block assembly. 250 mm 200 mm 150 mm j00 mm 150 mm 150 mm Answer: m y = 11 | Page
Write a conclusion about the image
A rod 3.5 feet long rotates in a horizontal plane about a vertical axis through its center. At each end of the rod is fastened a cord 6 ft. long. Each cord is inclined at Ø = 450 with the vertical and supports a weight of 45 lbsA. Which of the following gives the speed of rotation “n” in rpm?a) n = 25.12 rpm b) n = 25.12 rpm c) n = 30.20 rpmd) n = 22.13 rpm B. What is the tension in the 5 feet long cord? a) T = 58.47 lbb) T = 63.63 lbc) T = 51.78 lb d) T = 48.25 lb
Compare and contrast the advantages and disadvantages of analogous, parametric and bottom-up estimating
A scale drawing of a square desk is( 1)/(4) inch to 1 foot. The actual desk is 50 feet wide. What is the area of the desk in the model?
Q- What is the representative fraction for a scale of 10 cm=20 km? Represent the answer in the form of ratio.
kindly answer asap thanksWhat is the total area in square centimeters? What is the x-coordinate of the centroid of the shaded area (in centimeters) What is the y-coordinate of the centroid of the shaded area (in centimeters)
From the figure below, locate the centroid from x and y axes as shown.
Give me right solution according to the question
Determine the coordinates of the centroid for the given figure shown.