Select all statements that describe the mechanical properties of materials correctly (Hint: there are three right answers). Elastic materials can reveal a nonlinear stress-strain relationship. The Poisson's ratio can reach 1.5 in most engineering materials. The Hooke's law can describe the stress-strain relationship for any linear elastic materials. A secant (modulus) method can be used to approximately obtain the Modulus of Elasticity from nonlinear stress-strain curves. A nonlinear elastic response shows that a loading path should be different from the unloading path in the stress-strain curve.

Select all statements that describe the mechanical properties of materials correctly (Hint: there are three right answers). Elastic materials can reveal a nonlinear stress-strain relationship. The Poisson's ratio can reach 1.5 in most engineering materials. The Hooke's law can describe the stress-strain relationship for any linear elastic materials. A secant (modulus) method can be used to approximately obtain the Modulus of Elasticity from nonlinear stress-strain curves. A nonlinear elastic response shows that a loading path should be different from the unloading path in the stress-strain curve.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain. Determine the strain components εn, εt, and γnt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle θ. Sketch the deformed shape of the element. εx = -950 με, εy = 290 με, γxy = 1450 μrad, and θ = 35°.
The state of stress at a certain point in a stressed body is shown in figure. The magnitudes of normal stresses in x & y directions are 100 MPa& 100 MPa respectively. Determine the radius of Mohr's circle representing this state of stress (in MPa). Oy 0x4 9. Ox
A thin rectangular plate ABCD is deformed into a parallelogram as shown in the figure below. The width of the plate is w = 1200 mm, and the height of the plate is h = 2000 mm. The shear strain at A is known to be +3650 µrad. Assume a = 1.8 mm. Calculate the magnitude of dimension b in the figure. D Answer: b= i W B a mm X
It can be assumed that long cylinders, e.g. those used in pipelines, are subject to a state of plane strain, where the longitudinal strain is neglected in comparison with other strain components. The 3-dimensional state of strain at material point of a long cylinder in a pipeline, described in X, y, z coordinates, where the pipeline is extended in the y-direction, is given by: E. xx E yx -200 0 -180 [e ]= E, E, E = *10-6 ху yy Ezy [Ex E E= -180 0 50 yz a. Calculate the volumetric strain and the deviatoric strain invariants b. Calculate the mean stress and the deviatoric stress tensor. c. Calculate the characteristic equation of strain. d. Calculate the characteristic equation of stress. The material is linear elastic (E=200GPA, v=0.3).
A cross section of an engineering structure made of steel is shown in the Figure. For an applied torque of T = 175 N.m, (a) determine how much torque is carried by each of the two cross-sectional components and (b) the angle of twist per unit length. The shear modulus G = 200 GPa. (Neglect the stress concentrations). 45 mm 40 mm 4 mm 60 mm 4 mm 4 mm 120 mm 6 mm
The uniform forces U and P are applied to a plate with dimensions of 500mm x 400mm and a thickness of 10 mm as illustrated. Consider the linear elastic behavior, 200GPa Young's modulus, and 78GPa shear modulus. The plate is subjected to a uniform force U with an undetermined magnitude and direction and a uniform tensile force P=50KN. X 500 mm 400 mm A. What is force U, in kN, if deformation along y is zero? Is it a compressive or tensile force? B. What is the x-axis deformation, in mm? Is the dimension growing or shrinking?
As seen in the figure, a rigid beam carried by three elastic rods of equal length from points A, B, and C is pulled to Eve from points F by P-force. The modulus of elasticity of the bars are E1=100GPa, E2=120GPa and E3=100GPa. Yield stress σA=40 MPa for bar 1 and 3, yield stress σA=120 MPa for bar number 2. Accordingly, a) determine the load PA that will start the flow, b) the load PG that will cause the migration.
An element is subjected to plane stresses as shown in Figure Q1. (i) Determine the normal stress and shear stress acting on the plane that is inclined at 20° as shown in the figure. (ii) Determine the principle major and minor stress and the orientation of the plane where the stresses acting. (iii)Determine the maximum shear stress and the orientation of the plane. 10 N/mm² 30 N/mm² 50 N/mm² 2007 50 N/mm² 30 N/mm² 10 N/mm²
Determine the equivalent state of stress on an element at the same point oriented 60" clockwise with respect to the element shown in the figure below. Suppose that =153 MPa =D 109 MPa (Figure 1) Figure 1 of 1 75MPA
The state of strain at the point has components of € = 300 (10-6), y = -260 (10-6), and Yay = 460 (10–6). Figure
The strain components εx, εy, and γxy are given for a point in a body subjected to plane strain. Determine the strain components εn, εt, and γnt at the point if the n-t axes are rotated with respect to the x-y axes by the amount and in the direction indicated by the angle θ. Sketch the deformed shape of the element. εx = -1200 με, εy = 240 με, γxy = 1350 μrad, and θ = 36°.
Which of the following is NOT true of Elastic Modulus. It can be looked up using the Material Properties table in the textbook or another similar source like engineeringtoolbox.com It is a material property and should be approximately the same value for samples of the same material It describes the behavior of a material after yielding (permanent deformation). It links stress and strain, allowing us to predict things like a change in material shape due to a specific load. 2000