Calculated a) as 16.554kN, b) as 26.003kN and c) as 0.637mNeed help with d) and e) segmentQuarter circle,gateradius rdensity p4r4rA segment gate of radius 1.5 m and width 1.5 m is submerged in water as shown in the figure.Note the water level is such that a quarter circle is submerged.a) Find the horizontal component of thrust, F,.b) Find the vertical component of thrust, Fy.c) Determine the distance x (m) in the horizontal direction from the wall below the gate to the line of application of the vertical component of thehydraulic thrust on the gate.d) Determine the distance y (m) from the water surface to the line of application of the horizontal component of the hydraulic thrust on the givensegment gate.e) Determine the magintude of the total hydraulic thrust for the same quarter circle.

There are two types of forces that are acting on a circular surface. One type of force is Radial…

segment Quarter circle, y gate radius r G: density p 4r 4r 37 A segment gate of radius 1.5 m and width 1.5 m is submerged in water as shown in the figure. Note the water level is such that a quarter circle is submerged. a) Find the horizontal component of thrust, F,. b) Find the vertical component of thrust, F,. c) Determine the distance ¤ (m) in the horizontal direction from the wall below the gate to the line of application of the vertical component oft hydraulic thrust on the gate. d) Determine the distance y (m) segment gate. the ater surface to the line of application of the horizontal component of the hydraulic thrust on the giv

segment Quarter circle, y gate radius r G: density p 4r 4r 37 A segment gate of radius 1.5 m and width 1.5 m is submerged in water as shown in the figure. Note the water level is such that a quarter circle is submerged. a) Find the horizontal component of thrust, F,. b) Find the vertical component of thrust, F,. c) Determine the distance ¤ (m) in the horizontal direction from the wall below the gate to the line of application of the vertical component oft hydraulic thrust on the gate. d) Determine the distance y (m) segment gate. the ater surface to the line of application of the horizontal component of the hydraulic thrust on the giv

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Solve for a) only. You are free to make assumptions.
For purposes of analysis, a segment of the crank-shaft in a vehicle is represented as shown in the next figure. Two loads P act as shown, one parallel to -xo and another parallel to +zo. Each load P equals 1.0 kN. The crankshaft dimensions are b₁ = 80 mm, b₂ = 120 mm, and b3 = 40 mm. The diameter of the upper shaft is d = 20 mm. Investigate the stresses at point A, which is located on the surface of the upper shaft at the zo axis, and point B, which is located on the surface of the shaft at the yo axis. B Уо b₁ = 80 mm ZO A d = 20 mm b₂ = 120 mm b3 = 40 mm P = 1.0 kN ΧΟ
The expected value of the voltage across a resistor is 10V. However,measurement yields a value of 8.0 V. Calculate: a)Absolute error b)%error c)% accuracy
2. If a system is subjected to a sudden non-periodic force, the answer shall be: a) Periodic b) Constant c) Transitory
A hollow sphere rolls on a platform 2m long. The platform is inclined to 30o with the horizontal. Find the velocity of the center of mass when it descends completely the platform. The muzzle velocity is zero and the sphere rolls without sliding. A.) 1.28 m/sB.) 2.45 m/sC.) 3.43 m/sD.) 4.67 m/sE.) 5.78 m/sF.) 6.43 m/sG.) 7.89 m/s
I need the answer as soon as possible
i need the answer quickly
A sharp knife can cut because the pressure increases when a) the surface of contact is small b) the surface of contact is large c) when we apply a large force on it regardless of the surface of contact d) both the surface of contact and the force are large
This question is based on satellites, so I kept it under mechanical engineering. The question is attached as an image. Thank you.
Please answer all thank you(6)
20. A light is placed on a horizontal ground 40 ft from a building. A man 6 ft tall walks from the light toward the building at a rate of 5 ft/s. Find the rate at which his shadow on the building is decreasing when he is 16 ft from the building. A) 2.896 ft/s B) 2.333 ft/s C) 2.083 ft/s D) 2.667 ft/s
Please answer legibly. Heat and Mass Transfer - Heat Exchanger Water at 95°F is heated with steam up to a temperature of 212°F. The mass of water is 110 lb and the heating times takes 1200s. a) Find the heat transfer rate of the process. Assuming 1-1 heat exchanger. b) Calculate the total area from a) given overall heat transfer coefficient is 14 BTU/hr·ft2·°F c) From b), how many tubes of 2.5 in diameter and 12ft length should be used?