Seepage force per unit volume can be expressed as (A) iy,L (B) iL (C) Y,h (D) iy,

Q: The bar shown in the following figure has a diameter of 40 mm and is subjected to a force P = 1500 N…

A: Moment at given section due to load PM1=1500×150=225000 N.mmMoment at given section due to load…

Q: H.W A rigid slab weighing 600 Kw is Placed uron two bronze vads and one Steel Vocd Cnch of bo00 mm?…

A: Given:-m = 600 kN=600*1000 NArea of two bronze rods = Area of one steel rod = 6000mm2T = 15 degree…

Q: A Solid bar having a diameter of 160 mm is to be replaced by a rectangular tube having…

A: The maximum shear stress for solid bar is τmaxSolid bar=16Tπd3 The maximum shear stress for…

Q: 3.7-2 A motor drives a shaft at 12 Hz and delivers 20 kW of power (see figure). (a) If the shaft has…

A: Given,  Power delivered  Where we know that Shaft frequency (f) = 12 Hz

Q: 1. A steel rod is positioned vertically as shown in the figure. It is fixed at one end and…

A:

Q: Determine the threshold torsion

A: Torsion is the bending of a pillar under the activity of a force. It is methodically applied to…

Q: 3) Determine the change of volume caused in the block due to the application of the forces (Bulk…

A:

Q: 30kg and ma= 70 kg. Between all of the contacting swrfaces, u, = 0.1. What is the largest force F…

A:

Q: Determine stress

A: Given data : Force (F)=75 KNWidth (B)=20 mmDepth (D)=25 mm

Q: a.) Find the bulk modulus of elasticity of a liquid if a pressure of 150 psi applied to 10 ft3 of…

A:

Q: A reasonable approximation for the two-dimensional incompressible laminar boundary layer on a flat…

A: Given- u=U2yδ-y2δ2   for y≤δ

Q: 5Q. The plate is moving at 0.6 mm/s when the force applied to the plate is 4 mN. If the surface area…

A:

Q: A rod is composed of copper and steel section rigidly bolted in the wall as shown in the figure. If…

A:

Q: Given: • Rod A: Length = 40mm Rod B: Length = 60mm Determine: ● ● Area = 3 cm x 3 cm Area = 4 cm x 4…

A: Given data  P = 100 KN  EA = EB = 200 GPA = 200 × 103 N/mm2    Area of rod-A (AA) = 3cm × 3cm = 30mm…

Q: Q2: Use dimensional analysis to derive an epresion for the power developed by an engine in terms of…

A: Given Power=P Torque=T Rotation speed=ω

Q: Water from a reservoir flowing through a deformable 600mm diameter pipe with a velocity of 2.5m/s is…

A:

Q: 1500 KN 800 mm 70 mm 100 mm 1500 KN A bar has a length of 800 mm, width 100 mm, and thickness 70 mm,…

A: Length, L = 800mm Width, B = 100mm Thickness, T = 70mm Axial tension, P = 1500kN New length, L1 =…

Q: A wood beam carries the loading shown in the figure. Determine the smallest allowable width b of the…

A: given- working stress σ=10 MPacross section area A=200 mm×b mmwhere,b=smallest allowable width To…

Q: The intensity applied to beam AB is increased by a factor of 2. (i.e. your answer for the ntensity…

A:

Q: civil engineering Article Determine ( ↑ 0.3mm A=1m² केतिला Top plate 2 kinematic viscosity 3…

A:

Q: DETERMINE THE STABILITY, DETERMINANCY AND DEGREE OF INDETERMINANCY.

A: Ds=m+R-2j where m=number of members R=support reaction j=number of joints

Q: A 40 mm diameter rod 6 m long elongates 12 mm under a load of 240 kN. The diameter decreased by 0.…

A:

Q: A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's…

A:

Q: The height of the capillary rise of water increases as particle diameter increases True O False O…

A:

Q: A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the…

A: Given overhang beam with loading and asked to calculate shear stress below 50 mm from top fibre at…

Q: The quadrilateral plate (negligible weight) shown below is loaded with a block of weight, W = 68 kN,…

A: To find the abscissa of the loading point A

Q: Plate with 0.13m wide and 0.25 m length passes thru oil ewith layer 3.5mm and 5mm thick. Both…

A:

Q: TWO CONCRETE BLOCKS WEIGHING 1800 N EACH FORM PART OF THE RETAINING WALL OF A SWIMMING POOL. WILL…

A: Given:   Weight of each block    =1800 N Friction coefficient at the base of the first block,…

Q: get. The shear stress at a point in a liquid is found to be 0.03 N/m². The velocity gradient at the…

A: Given data : Shear stress (ζ)=0.03 N/m2Velocity gradient dudY=0.15 s-1

Q: The thin walled cylinder diameter whose diameter is 6.24 meters and thickness of 15mm. is subjected…

A:

Q: A steel penstock 60 cm in diameter has a shell thickness of 1.2 cm. The modulus of elasticity of…

A:

Q: The acrylic plastic rod is 200 mm long and 15 mm in diameter. If an axial load of 400 N is applied…

A:

Q: a) 128.5 GPa A circular rod of diameter 30 mm and length 200 mm is subjected to a tensile force. The…

A: Given, Diameter of the rod = D= 30mm Length= L= 200mm Change in length, ∆L= 0.09 Change in diameter,…

Q: A beam shown below, 200mm wide by 350mm deep, is loaded as shown in figure below. Determine the…

A:

Q: A circle of diameter d = 225 mm is inscribed on an unstressed aluminum plate of thickness t = 18 mm.…

A:

Q: Determine induced stress

A: given data : length (L)=5 mmt1=15∘Ct2=40∘C

Time and time related variables in engineering

Time is the event progression starting from past to present and then, future statistically. The time-related variable is any particular value in relation to time to assess its changes on a specified (XY) plane.