section width is reduced to IS m and channel D.50m.Find the change in water surface elevation.

Q: What is adsorption zone?

A: The deposition of molecular species onto the surface of any object is known as adsorption. The…

Q: Design Calculation of stair climbing trolly

A: In day today life we may have to carry so many goods and objects of various quantities through…

Q: Members BE, CE, and CF

A:

Q: Define Reliability-based design

A: Reliability-based design- It is defined as a  concept that helps in planning, building, and…

Q: View Policies Current Attempt in Progress The solid 1.05-in.-diameter rod is subjected to a uniform…

A:

Q: PROBLEMH2 ww 9. ww a. WwW SDLVE FOR Rab

A: Given:-

Q: What is wrong with the picture at right?" (<25 words) YES! Safel NOI Unsafel

A: A picture including of two images where different cases of cylinders were given.

Q: Define Eccentricity,

A: Eccentricity is a term is used in the loading condition of the engineering. for example, the load on…

Q: Define Bearings?

A: Bearing: It is defined as the angle which is measured between the reference meridian and the survey…

Q: Whose responsibility is it to create the as-built BIM? Architect / Engineer to complete designers'…

A: This question is related to the Building design from Civil Engineering.

Q: The Vicatronic

A:

Q: Define ULS requirement

A: The Ultimate Limit State is abbreviated as ULS.

Q: Define Dilatancy.

A: Dilatancy is the property of dense packed granular material in which the volume increases while…

Q: What is susbtainable design?

A: Answer Introduction Sustainable design is defined as these are those that seek to minimize the…

Q: What is the most common use of RFI?

A:

Q: How does USGBC operate?

A: - USGBC is acronym for United States Green Building Council. - USGBC is formed to provide new…

Q: Draw the complete shearing force diagram and bending moment diagram for the beam shown below. State…

A: A beam is simply supported at two ends. Two UDLs of 500 N/m at each end 0.3 m from the supports A…

Q: ONS B.S. H.I. F.S. LF.S. ELEVATIONS -a 1.24 234.51m 1.11 3.40 4.6 2.8 3.6 2.4 3.21 2.46 1.2 3.2 2.8…

A: Given profile levelling HI = elevation +   BS elevation = HI - FS or IFS given elevation of BM a =…

Q: can u get the

A:

Q: What is Third Party Certification?

A: When an item or organisation has the formal verification or authentication of certain…

Q: Define Full form of "CASBEE"

A: CASBEE is a tool for assessing and ranking building and design and environmental efficiency. It is a…

Q: Is there anything special about a CPLD

A: Several different types of the PLDs which means programmable logic devices are existed such as FPGA,…

Q: +4

A: Given

Q: Confirm that the force field F(r, y) = 2cy'i + 3x*y²j is conservative in some open connected region…

A: solution Given force F=2xy3i+3x2y2jpoints P -9    4and Q=6    1the work done by the particle is…

Q: RITING ITLED d. What is the difference in elevation between TP15 and TP30? (Ans.) e. What is the…

A:

Q: Define Dynamic Replacement.

A: Dynamic Replacement is the dynamic compaction variation, and comprises of delivering energy of…

Q: Identify all ZERO force members

A:

Q: ments Collaborate 此片 Freak Out Slice Crop Horizontal Start New Sheet Sketch Sketch Sheets 5 LBS…

A:

Q: BED 3 43 x 3.60 BED 2 BATH 2.79 x 358 3.43 x 3.60 W.I.R. 2.33 x 1.06 W.I.L. .93 x 104 W.I.R. 1.35 x…

A: A block in AutoCAD is simply a collection of objects which are grouped together to form a single…

Q: *HW to be submitted today before 12:00 AM Feb 23 ABニ- (T,C) BCニーN(T) Nc) Detevmine 750N O AB= the…

A: Method of joint is one of the method to determine force acting in members. In this method each joint…

Q: 4#8 12" 15" I 3: fó= tooopsu Grade Go Steel NWC. &Mn = ?

A:

Q: Define Bulldozers.

A: Bulldozer is very large, powerful and heavy construction equipment which is used for pushing large…

Q: "-Q3.33-. A cantilever beam as shown in the figure has a clear covering of 50 mm at the top and at…

A:

Q: 5. Provide the missing bearings of the following=

A: solution Given line ABForward bearing =N44°38'E the whole cicrle bearing =44°38'as we know back…

Q: Kindly solve this question under Measurement and Specifications for Civil Engineers.

A: Based on the information provided and the Contract Specifications, here's the takeoff for the…

Q: What do you mean by fail safe design

A: Fail-safe designs are the methods of designs in which various techniques can be used to mitigate…

Q: Pen raser Unco Redo The flat pattern has red and green lines drawn on the surface of the paper. Draw…

A: The flat pattern has red and green lines so that the 3D shape drawn below ,

Q: 3. A circular steel bar with cross sectional area of 4 in is loaded as shown. a) Compute the shear…

A:

Q: P-80 N 40 F=200 N 200 mm W=140 N 1 V3 C= 20 Nm FIGURE C 100 mm H 90 N 200 mm 400 mm 6. An angular…

A:

Q: Station End area fill (sf) Distance (ft) Volume (cy) 150 + 00 360 150 + 50 3,500 50 151 + 00 10,400…

A: use mean area method to find the volume mean area is found out by using Amean=A1+A22volume V=…

Q: How to identify if "cos" or "sin" is to be used?

A: If force makes angle with x-axis, cos component will be considered along x-axis and sin component…

Q: Based on the attached enlarged floor plan, how many sq. m. of 16mm (5/8") plywood backing is…

A: Grab bars are graspable bars to help maintain balance and lessen fatigue while standing. They are…

Q: How many studs are require for the exterior wall on the main floor if there are two doors and 6…

A: Hi! Thank you for the question As per the honor code, We’ll answer the second and third question…

Q: What is specific gravity (sp gr)

A: Given data in question  Specific gravity  To be discussed  What is specific gravity    Specific…

Q: i…

A:

Q: GIVE THE FIVE ELEMENTS OF GREEN BUILDING

A: Green building is a design strategy that tries to reduce a building's environmental effect while…