Say a little prayer, then proceed!!!! Set B: For Student number ending EVEN number and Zero V₂(8) Problem 1 Find the transfer function R₁ R₂ www vc (1) v(1) V(s) 0000 i₂(1)

Q: Explain how the wind drives the blade of a wind turbine

A: Wind turbines are tall structures that consist of tall towers mounting a blade that rotates due to…

Q: Design a circuit and write an Arduino code to displays "5 seconds elapsed" and blink an LED every 5…

A: It is asked to design a circuit and write an Arduino code to displays "5 seconds elapsed" and blink…

Q: The Voltage between the contacts during the arcing period is Land is just sufficient to_ O a. Very…

A: Vacuum circuit breaker.  Vacuum circuit breaker has minimum gap between fix and moving contact.

Q: For protecting of hands resistant gloves are made up of plastic.

A: Chemical resistant gloves are made of plastic.

Q: The figure below shows a loạding truck in a cement factory. The truck has three wheels, front wheel…

A: According to the question, we need to design a control circuit by using a multiplexer that operates…

Q: ow does an intermediate switch work?

A: The explanation is as follows.

Q: A circuit has two pushbutton switches connected to pin PB2and PB3 and two LEDs connected to pin PC0…

A:

Q: searching for the topic of production lines and the switches in them and PLC in production lines +…

A: Step 1:  Step 3: Step 4:

Q: A speedometer is connected in an automobile system to measure the speed. The meter reads 120.8 rpm…

A: In this question we need to choose a correct option

Q: 2.46 Find I in the circuit of Fig. 2.110. 20 Ω 15Ω 12Ω ww ww 15Ω ww 15 Ω 80 V 5Ω 24 2 Figure 2.110…

A:

Q: Write an Arduino code to control two LEDs using two push buttons, given the bellow setup: LED 1 is…

A: The LED pins should be used as output pins and Button pins should be used as Input pin in program.

Q: 21. Which voltage range that is sometimes called a “float" in TTL circuits?

A:

Q: Create a Sequence Diagram about Temperature Controlled Electric Fan with the following: *Thermistor…

A: Sequence Diagram of temperature controlled electric fan shows that how the fan works with the sensor…

Q: 1. What motor is used in the washing machines? Explain in detail the construction and working of the…

A: Brushless DC (BLDC) motor is used in the washing machines. CONSTRUCTION -: The main difference…

Q: Crystal radio receiver Please explain how this circuit works

A: NOTE- According to the policy, we can answer only one question, please post other question as…

Q: of the following statements is true for an SCR. It is an on-only controllable switch, which is…

A: There are three types of switches: Uncontrolled switches : In these turn on and turn off can not be…

Q: Computer Digital Logic. Design 4 X 1 Multiplexer.

A: The 4 X 1 Multiplexer has 4 inputs and 1 output. The block diagram of the 4 X 1 Multiplexer is shown…

Q: Explain how the IGBT switch works. Draw the symbol and its characteristic curve.

A: The IGBT is a power switching transistor having advantages of MOSFETs and BJTs for use in power…

Q: Power electronic controllers have OLow overhead capacity OHigh overhead capacity ONo overhead…

A: In this question we need to choose a correct option

Q: What is the name and function of this symbol?

A:

Q: Chose the Q/ For the type E chopper to be operated in the fourth quadrant? A. only switch is…

A: type E  chopper : a four quadrant chopper is a chopper which can operated in all the four quadrants…

Q: Where does 23/332 for N1/N2 come

A:

Q: Q-1) هد Please write the magnetic circuit And explain the steps.

A: Given figure:Asked to explain the ircuit and write magnetic circuit?

Q: In short tell about plc.

A: The PLC is defined as the Programmable logic controller and it is a specially designed controller to…

Q: 5. What is the purpose of a starter?

A: A glow switch starter, sometimes known as a glowbottle starter, is a form of fluorescent light…

Q: What kind of sensor is this type O a. magnetic O b. inductive O c. float O d. pressure

A: What type of sensor is given in the above image ? A. Magnetic  B. Inductive  C. Float  D. Pressure

Q: Problem 1 is a review of your understanding of KVL (Kirchhoff's voltage law) Using KVL find the…

A: A simple question based on network analysis and the topics described in the solution are kirchoff's…

Q: Horizontal Controls Autoset tical Controls Trigger Controls

A:

Q: Why switching circuits are called as finite state systems

A: In this question we will write about why switching circuits are called as finite state systems.....

Q: f I were to fill in the table to have a robot follow a line being detected by the three sensors, how…

A:

Q: Which one is the true statement a. Open loop systems are less affected by noise b. Open loop systems…

A: For option (a): Open loop control System. This type of control system does not have any feedback and…

Q: IV- Define with draw the block diagram the sensor fusion.

A: Sensor fusion aims to overcome the limitations of individual sensors by gathering and fusing data…

Q: DESCRIBE THE PURPOSE OF MULTIPLIERS IN SERIES & SHUNTS ACROSS A METER MOVEMENT.

A: SOLUTION MULTIPLIERS                        Multipliers are used to…

Q: b) Define any 4 time domain specification parameters Also Identify () Delay time (i) Peak Time (i)…

A: (ii) Peak time  tp = 0.5 sec tp=πωd ωd=πωd ωd=π0.5    =2π so delay time will be  (I)Delay time td=…

Q: what electrical symbol is this ??

A: The given symbol is Now, Consider the various symbols for inductors: 1) Air-core Inductor 2)…

Q: State two function of the following 1. A.L.U 2. control unit 3. Register

A: ALU: ALU stands for Arithmetical Logic Unit is used to perform the arithmetic operation and logic…

Q: give the following about SWITCH: Advantage Disadvantage When to use?

A: The switch is a very important component of a network it is important to deliver the network or…

Q: What does the DC NULL actually measures?

A: The DC null detector is a current galvanometer whose deviation is accompanied by uneven emf. It is…

Q: 4.-What is switch bounce? Describe two techniques to minimize switch bounce.

A: Brief Concept- Switch bounce- The brief separation of contacts that occurs when a mechanical switch…

Latches and Flip Flop

Just like logic gates, the latches and flip-flops are the important elements of an electronic circuit. The logic gates form the important part of combinatorial circuits, while the latches and flip-flops form the essential part of a sequential circuit. Sequential circuits form the important concept of automata theory in electronics and electrical engineering, these circuits are a kind of logic circuit whose output depends on both present input and past inputs, that is, the input history.