SAE 30 oil at 20°C flows in the 2.5-cm-diameter pipe as shown in the figure below, which slopes at 37°. For SAE 30 oil, take ρ = 891 kg/m3 and μ = 0.29 kg/m⋅s.                                                                      Determine the flow rate in m3/h.   The flow rate is  m3/h.

Q: Water is pumped through a horizontal, smooth circular pipe at a bulk velocity of 0.4 m/s. The pipe…

A:

Q: Determine the force P required to move the wedge to the right if the coefficient of static friction…

A:

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

A:

Q: s relative density is 0.85, its dynamic viscosity is 1.5 Pa.find the pumping power that must be…

A:

Q: Fluid A is three times denser than Fluid B through the same horizontal pipes. Which will flow…

A: The fluid is the substance that offers resistance to flow. Basic fluid properties are density…

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

A:

Q: Water is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular…

A: We have, Diameter, d=200 mm=0.2 m,     V=3 m/s Diameter of circular plate, d1=150 mm=0.15 m (as…

Q: Air flows through the 400-mm-wide rectangular duct at 75000 liters/min as shown in . Take pa = 1.202…

A:

Q: Current Attempemrogr039 Oil of SG = 0.87 and a kinematic viscosity v = 2.2 x 10-4 m²/s flows through…

A:

Q: A 1/4” inside diameter pipe is used to transport SAE 30 motor oil (µ = 0.006266 slug/ft-s and ρ =…

A:

Q: The diameter of an open-topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: Water "bubbles up" above the exit of the vertical pipe attached to three horizontal pipe segments.…

A:

Q: What is the pressure at point 2 (kpa), if the water flows as irrotational inside the pipe? Given…

A: Solution:

Q: The impact force exerted by water on the reduction element (spacer for reducing the pipe diameter)…

A: The solution of this question would require the impulse momentum equation, Bernoulli's equation and…

Q: The diameter of an open topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: The discharges from the pipe is 0.142 m3/s of water into a reservoir at a point 1.85 m below the…

A: Given:diameter at point A, da 0.254 mdiameter at discharge, d=30.5 cm or 0.305 mDischarge, Q=0.142…

Q: The power supplied to the fluid (QγHB/550) by the pump in the Figure is 10 hp. If H = 60 ft and the…

A: Given: The power of the pump is 10 hp.  H = 60 ft  D = 150 mm

Q: The figure represents a stream of water in a pipe. If the distribution of velocities in a section is…

A: For the solution refer below images.

Q: Q4/ Gas (p = 0.0022 lb/ft) flows through duct shown in fig. At A flow rate is 60 ft /s under a…

A:

Q: Problem 2- Determine the manometer reading as shown in the figure, when the velocity of fluid…

A:

Q: A piston contains a type of fluid that has a S.G of 0.9 and a dynamic viscosity of 0.02 Poise. The…

A: Given question belongs to subject Fluid Mechanics and can be solved using Continuity equation.…

Q: AAA cir Water is flowing through a horizontal pipe of diameter 200 mm at a velocity 3 m/s. A…

A: Given:pipe diameter, D=200 m or 0.2 mvelocity of flow, v=3 m/sdiameter of solid plate, d=150 mm or…

Q: Water circulates through the Venturi tube shown at 80°F. If an ideal flow is considered (without…

A:

Q: Oil (Gs = 0.80) flows through pipe A at 200 li/s at elevation 20 m through a 200 mm diameter pipe…

A:

Q: Oil of SG = 0.87 and a kinematic viscosity v = 2.2 x 10-4 m²/s flows through the vertical pipe shown…

A:

Q: Oil with viscosity 7.8 x 10-4 lbs and specific weight 59 flows through the funnel below. ft²…

A:

Q: Water with a density of 999.1 kg/m3 and absolute viscosity of 1.138 X 103 kg/m-s is flowing steadily…

A:

Q: A venturi meter is introduced in a 300 mm diameter horizontal pipeline carrying a liquid under a…

A: Given data: D=300 mmd=100 mmP=150 kPaHead loss=3% of differential pressure headhloss=-400 mm Need to…

Q: is flowing through a horizontal pipe of diameter 200 mm at a velocity of 3 m/s. A circular solid…

A: Given:Pipe diameter=200 mm or 0.2 mvelocity=3 m/s

Q: There is an upward flow from the vertical pipe shown in the figure. If the flow rate is 0.05 m3 / s,…

A: Given data: The flow rate is, Q̇ = 0.05 m3/s. Write the expression to calculate the velocity at…

Q: According to Torricelli´s theorem, the velocity of a fluid discharging through the hole of a…

A: Given: The tank with water is shown below: Area of the tank is Ab. Area of the hole is Ao.

Q: Calculate the shear stress in lb/ft2 at the centerline of the 4.7-inch diameter pipe carrying water…

A:

Q: The net pressure force along the horizontal direction (N). Net out flow rate of momentum through the…

A: As per honor code and answering guidelines I can answer 1st, 3 sub parts at time .If you want other…

Q: A 1.5-in-diameter water jet with a velocity of 100 fps impinges on a single vane moving in the same…

A: From the given data:

Q: The diameter of an open-topped tank 1.5 m high increases uniformly from 4.2 m at the base to 6 m at…

A:

Q: Water flows steadily with negligible viscous effects through the pipe shown in the figure below.…

A:

Q: Air flows through the 400-mm-wide rectangular duct at 75000 liters/min as shown in . Take p, = 1202…

A: Given:w=400 mm or 0.4 mQ=75000 liters/minQ=750001000×60=1.25 m3/sρa=1.202 kg/m3

Q: A piston contains a type of fluid that has a S.G of 0.9 and a dynamic viscosity of 0.02 Poise. The…

A: The density of the given fluid is The dynamic viscosity of the fluid is Since 1 poise is equal to…

Q: Calculate the flow rate of the system by accepting the fluid passing through the reservoir-pipe…

A:

Q: 8 m/s y 100 mm -X 30⁰ B. 100 mm

A:

Q: The water temperature in the tank is 60 °C and the pump has the capacity of 20 ton/hour. Pump is 2m…

A:

Q: Given an open tank filled with oil that is discharging through a 35-meter long commercial annulus…

A: GivenRi=2cm=0.02mdi=0.04mh=5mS.G=0.9L=35mμk=4×10-5 m2/s

Q: Your team is designing a chemical processing plant. You are the liquid handling and transportation…

A:

Q: Problem Consider a cylindrical pipe of length L and diameter D = 2R. The angle that the axis of the…

A: The suspicions of the situation are that the liquid is incompressible and Newtonian; the stream is…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.