s(1 Consider a serial bus (1 bit wide) that runs at 2GHZ, using alternate cycles for control signals and the other half of the cycles for data. What is the throughput of the bus in bytes/second? Assume you wantto attach a video camera using this bus. The camera generates 60 frames per second, with each frame containing 1 Million pixels, each pixel 4 bytes in size. Would this work? Answer one of the below: a) If not, what compression factor would the camera need to achieve to be supported? A compression factor describes how much smaller the data is when compared to un- compressed data. b) If yes, how many cameras could be connected?

s(1 Consider a serial bus (1 bit wide) that runs at 2GHZ, using alternate cycles for control signals and the other half of the cycles for data. What is the throughput of the bus in bytes/second? Assume you wantto attach a video camera using this bus. The camera generates 60 frames per second, with each frame containing 1 Million pixels, each pixel 4 bytes in size. Would this work? Answer one of the below: a) If not, what compression factor would the camera need to achieve to be supported? A compression factor describes how much smaller the data is when compared to un- compressed data. b) If yes, how many cameras could be connected?

Database System Concepts

7th Edition

ISBN:9780078022159

Author:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Publisher:Abraham Silberschatz Professor, Henry F. Korth, S. Sudarshan

Chapter1: Introduction

Section: Chapter Questions

Problem 1PE

See similar textbooks

Related questions

Q: Consider two raster system with the resolution 640 * 480 and 1280 * 1024. How many pixels could be…

A: A) Given that 120 frames are refreshed per second in 640*480 system, access rate is 640*480*120 =…

Q: Do you prefer asynchronous or synchronous buses in terms of the amount of processing power and…

A: Synchronous buses operate on a clock signal, which synchronizes data transfers between components.…

Q: Question 2 n Figures 2, 3, 4 and 5 the designation of the state of the MISO signal is "Hi-Z" before…

A: Answer:

Q: 2. Computer A has an overall CPI of 2.5 and can be run at a clock rate of 900 MHz. Computer B has a…

A: Note : Answering the question 2 as per the instruction given in question. Given Data : Computer A :…

Q: 2) Consider three different raster systems with resolutions of 800 by 600, 1280 by 960, and 1680 by…

A: To calculate the Frame buffer size with 16 bits per pixel for each of the system is, 8 bit = 1 byte,…

Q: Construct a bus system with MUXs for 6 registers each of 8 bits.

A: Given:

Q: is to be connected to a high- definition video card that is supporting a 1920x1080 true-color (3…

A: The data rate as, = (Number of frames per second) * (Number of pixels per frame) * (Number of bytes…

Q: A certain computer’s Datapath takes 3.86 ns to load data from registers, 13.94 ns to execute the…

A: Given, Datapath takes 3.86 ns to load data from registers 13.94 ns to execute the ALU 5.99 ns to…

Q: Consider TDM-based circuit switching with 8000 frames per second and 32 time slots per frame. During…

A: Given, TDM-based circuit switching with 8000 frames per second 32 time slots per frame During each…

Q: Consider a memory system with the following parameters: Tc = 100ns Cc = 0.01…

A: Given Tc = 100ns Cc = 0.01 cents/bit Tm = 1,200ns, Cm = 0.001 cents/bit a) What…

Q: A system bus is used to carry data between two or more components of the system. Since an 8-bit…

A: System bus- A bus with three interconnected buses inside it is called a System bus. Three…

Q: Suppose you have an LFSR with state bits (also known as the seed) (S5, S4, S3, S2, S1, So) = (1,0,…

A: Seed: (s5, s4, s3, s2, s1, s0) = (1, 0, 0, 1, 1, 0) Tap bits: (p5, p4, p3, p2, p1, p0) = (0, 1, 1,…

Q: Design a 16-bit common bus system using tri-state buffers and other devices you may need. The…

A: The bus system will be built utilizing various multiplexers and tri-state gates that are known as…

Q: Lonsider an 8-bit ALU with 4-bit status register. The four status bits ar ymbolized by C, S, Z, and…

A: We are going to perform binary subtraction and based on the result obtained we will update status…

Q: 33. Suppose that a bus has 16 data lines and requires 4 cycles of 250 nsecs each to transfer data.…

A: Question: Suppose that a bus has 16 data lines and requires 4 cycles of 250 nsecs each to transfer…

Concept explainers

Computer Fundamentals

The computer is termed computation. For calculating or computing something the device that has been used is known as the computer. Or we can say that for performing a fast arithmetic operation the device that has been used is a computer. Storing, processing, and retrieving are the main features of a computer. 

Question

4.
bus throughput
Consider a serial bus (1 bit wide) that runs at 2GHZ, usingalternate cycles for control
signals and the other half of the cycles for data.
What is the throughput of the busin bytes/second?
Assume you wantto attach a video camera using this bus. The camera generates 60
frames per second, with each frame containing 1 Million pixels, each pixel 4 bytes in
size.
Would this work?
Answer one of the below:
a) If not, what compression factor would the camera need to achieve to be supported?
A compression factor describes how mu ch smaller the data is when compared to un-
compressed data.
b) If yes, how many cameras could be connected?

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, computer-science and related others by exploring similar questions and additional content below.

Similar questions

Consider two raster systems with the resolutions of 640 x 480 and 1280 x 1024. a) How many pixels could be accessed per second in each of these systems by a display controller that refreshes the screen at a rate of 60 frames per second?
Give an explanation of the differences between data buses, address buses, and control buses.
Q2: A gaming device has to transfer a high definition 1280 x 720 x 3 video frame @ 30 frames/sec. The 32-bit system bus operates in burst mode (burst size of 4). It takes one clock cycle to make one transfer through the bus and there is an overhead of five clock cycles per transfer. What should be the minimum bus frequency?
Please help with this problem about Pulse Width Modulation.
https://www.analog.com/en/analog-dialogue/articles/introduction-to-spi-interface.html
A 16Kx4 memory uses coincident decoding by splitting the internal decoder into X-selection(Row Address) and Y-selection (Column Address).a. What is the size of each decoder and how many AND gates are required for decoding theaddress?b. Determine the X and Y selection lines that are enabled when the input address has thebinary equivalent of 6000. Express X and Y in binary and their decimal equivalent.
Assume a bus is 16 bits wide. The data and address lines are multiplexed, meaning that the bus must alternate addresses one cycle and data the next. The bus runs at 300MHz. How long will it take to transfer 15MB over the bus?
The original IBM specifications for VGA specified a pixel clock speed of 25.175 MHz. What is the period (time for one clock cycle) of this clock? Express your answer in microseconds (μs) with 5 significant figures. Hint: The period is given by T = 1/f. Think about units and use a formula to convert as necessary.
Suppose you have an LFSR with state bits (also known as the seed) (85, 84, 83, 82, 81, 80) = (1, 1, 1, 0, 1, 1) and tap bits (also known as feedback coefficients) (P5, P4, P3, P2, P1, Po) = (0, 1, 1, 1, 0, 1). What are the first 12 bits output by this LFSR? Please enter your answer in the form of unspaced binary digits (e.g. 010101010101). These come in order $08182 ... $11.
A gaming device has to transfer a high definition 1280 x 720 x 3 video frame @ 30 frames/sec. The 32-bit system bus operates at 100MHz clock. It takes one clock cycle to make one transfer through the bus (i.e. D=1) and there is an overhead of ten clock cycles per transfer (i.e. O=10) Is this bus suitable for this system? If not, then what can be done to make it suitable? Explain. What if the bus operates in burst mode (burst size of 4)? Would it be suitable to use? Explain.
Do you like synchronous or asynchronous buses in terms of how much extra work they have to do and how much memory they use?a bus that goes all day and night without stopping? Explain.